Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFAAC Access Control Installation: The Summerlin Owner’s Guide
We install FAAC-compatible access control systems for Summerlin homeowners, and most jobs land between $650 and $1,850 installed depending on whether you’re replacing a keypad, a card reader, a loop detector, or the whole entry controller. Simple keypad and reader swaps can often be done same day, and we answer the phone around the clock. Access control rarely fails all at once. Summerlin owners usually notice a gate that won’t take the code it has taken for twelve years, a keypad whose buttons have gone soft, or an intercom that hums but never rings the house.

Which FAAC Models This Applies To
FAAC’s residential and light-commercial access control lineup spans the 844-series operators paired with 811/812 control boards, the 844 MC and 844 ER sliding and swing control panels, and the 531/532 barrier operators. Most of what we work on in Summerlin sits on the 844 platform, which has been stable for years but has a few version gotchas. The control board matters more than the operator itself. An 811 board revision from the early 2010s uses a different terminal mapping than the current 812, and a keypad wired to the older pinout will read but won’t trigger the relay. Before we quote anything, we photograph the board, read the label, and match firmware and terminal layout to the replacement. For OEM versus aftermarket: FAAC-branded boards and readers cost more but drop in with no rewiring, while quality third-party readers (BFT, DoorKing-compatible) can save real money if the board supports their protocol. We don’t carry stock, so the part is ordered to your actual model, not guessed from a photo you texted us.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your FAAC Access Control Installation Is Failing
- Code works, gate won’t open. The keypad is sending, but the 811/812 board’s relay has gone intermittent or a terminal screw has loosened from thermal cycling. Las Vegas Valley summers run the board box to 140°F inside, and solder joints that survived a decade up north frequently fail here.
- Keypad buttons feel spongy or need a hard press. The membrane has worn through under the silicone, common on FAAC 844 keypads exposed to west-facing afternoon sun in Summerlin.
- Reader beeps but won’t accept the card. Either the card’s credential has fallen out of the local database, or the reader’s antenna coil has cracked. On the 844 ER, this is usually the reader, not the board.
- Loop detector stays “triggered.” The exit loop under the driveway has lost continuity from a crack in the slab or a road-base settling. The gate never sees the “safe to close” signal and holds open.
- Intercom rings the house but no audio. The handset wiring or the 844’s audio module has failed, not the call button. Test the module before ordering a handset.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing in Summerlin, quoted before a single wire is touched:
| Item | Installed Range |
|---|---|
| FAAC-compatible keypad (residential) | $650 – $980 |
| Proximity card reader with credential setup | $720 – $1,150 |
| Loop detector replacement (including slab cut and re-pour) | $850 – $1,450 |
| Full 844 control board replacement with firmware match | $980 – $1,850 |
The range is driven by board revision, whether the existing conduit and wiring can be reused, and whether the intercom is wired or standalone. Pricing is settled upfront, in writing, and the price you agree to is the price on the invoice. Every access control job is covered by our 90-Day Done Right Promise, in writing.
DIY or Call Us?
You can safely check a few things: reset the breaker feeding the operator and see if the board’s LED comes back on, confirm the keypad’s battery if it’s battery-backed, and look at the loop cut in the driveway for visible cracks. What we don’t recommend is opening the control box and working live. The 844 board sits on 120V mains with a capacitor that holds a charge after power-down, and a slip on a live terminal is not a mistake a homeowner walks away from. Call us at (866) 623-9848 and we’ll diagnose it correctly, price it upfront, and get it right the first time.
FAQs
Eight to twelve years in a shaded enclosure, and closer to six to eight when the box faces direct afternoon sun or sits near the gate motor’s exhaust heat. Summerlin’s summer temperatures are the biggest single factor.
Sometimes. Loose terminal screws, dry relay joints, and firmware resets are repairable and we’ll tell you when repair is the right call. Once the board’s processor or a surface-mount IC has failed, replacement is more cost-effective than chasing the repair.
Keypad and reader swaps run 60 to 90 minutes on a typical residential install. Board replacements run 2 to 4 hours including firmware match and full re-test of every credential.
We match the exact model and board revision from your enclosure label, then order from FAAC-authorized distribution. We don’t stock parts, so what we install is the correct part for your gate, not a generic substitute. Ironworks Gate Co. Summerlin is an independent service provider and is not affiliated with FAAC.
We also service LiftMaster, Mighty Mule, and Ghost Controls operators. Call (866) 623-9848 for a free estimate.
Written by the team at Ironworks Gate Co. Summerlin, serving Summerlin and nearby areas.