Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFAAC Welding & Fabrication: The Summerlin Owner’s Guide
We repair and re-fabricate failed FAAC gate hardware across Summerlin, and most welding and fabrication jobs on FAAC arms, brackets and hinge mounts run $280 to $850 installed depending on what’s cracked and whether the operator has to come off the post. Repair calls are usually handled same day, and we quote a firm price before a single weld is laid down. Owners usually find the problem the hard way: the gate starts dragging at one end, the arm shudders or the operator grinds against a bracket that has quietly torn loose from its mounting plate.

Which FAAC Models This Applies To
FAAC swings between light residential arms and heavier articulated operators, and the fabrication work differs by series. The 400 and 390 lines are common on Summerlin driveway gates, and their mounting plates and arm brackets are the pieces we see fail most. The 740 and 760 articulated arms use a different yoke and anchor geometry, so a bracket that fits a 400 will not fit a 760. Before ordering anything, find the model plate on the operator housing or inside the control box cover, and measure the post-to-gate gap and the hinge offset. On FAAC specifically, the decision between OEM and quality aftermarket often comes down to the mounting hardware: genuine FAAC brackets hold their thread and fit; cheap aftermarket plates loosen and re-crack within a season. We are an independent service provider, not affiliated with FAAC, and we source the correct part rather than force-fitting whatever is on hand.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your FAAC Welding & Fabrication Is Failing
- Bracket cracks at the weld toe. Vibration works a hairline crack along the weld edge, and it grows each cycle until the arm shifts. A visible rust line at the joint is often the first sign.
- Gate sags or drags at one end. A fatigued hinge weld or a loosened mounting plate lets the leaf drop, so it scrapes the drive or the ground. Left alone, that drag loads the operator and shortens its life.
- Arm shudders or jerks mid-travel. A cracked anchor plate or a worn yoke weld lets the arm move out of alignment, and the operator fights the misalignment every pass.
- Operator grinds against the bracket. When a mounting weld lets go, the arm housing can foul the post or bracket, and the noise is the metal telling you it’s out of true.
- Rust streaks and paint flaking at joints. Summerlin’s dry heat and intense UV bake paint and trap grit at the weld line, so joints corrode faster here than owners expect from a gate that looks fine from the street.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Summerlin, welding and fabrication on FAAC hardware typically runs $280 to $850 installed. A straightforward bracket re-weld sits near the low end; a torn hinge mount or a full arm-plate re-fabrication with the operator removed pushes toward the top. The range is driven by how much metal has to be rebuilt, whether the operator comes off the post, and whether the gate needs re-hanging to bring the leaf back true. Parts and labor are quoted together so you see exactly what you’re paying for, and every job is protected by our written 90-Day Done Right Promise: if it isn’t right, we come back and make it right. We settle the price before work starts, so there are no surprises on the bill.
DIY or Call Us?
You can safely check the obvious: look for cracks at the weld toes, rust streaks at joints, a sagging leaf or a bracket that has shifted. Stop there. Welding on a loaded gate frame is genuine work for a trained technician, and an amateur repair on a stressed weld can fail under the gate’s weight or the operator’s push, which is a real injury risk. Re-fabricating a FAAC mount also means getting the alignment right, and a weld in the wrong spot can throw the operator out of spec. If you see any of the signs above, call us at (866) 623-9848 for a free estimate and a straight answer on what it needs.
FAQs
How long does a FAAC weld or bracket last in Summerlin? A properly re-fabricated bracket or hinge weld typically holds for years, but Summerlin’s sun and grit wear joints faster than a milder climate would, so an annual look at the welds pays off. Call (866) 623-9848 for an exact quote, and estimates are free.
Can this be repaired instead of replaced? Often yes. A cracked bracket or hinge weld is frequently re-fabricated rather than replaced outright, which keeps the cost down. We’ll tell you honestly whether a repair will hold or whether the part should be swapped. Call (866) 623-9848 for a free second opinion on any written estimate.
How long does the swap or weld take? Most FAAC bracket and hinge repairs are done in a single visit, and a lot of them are same day. A larger re-fabrication with the operator removed can run longer. Call (866) 623-9848 and we’ll give you a realistic window for your Summerlin gate.
How do you source the part? We identify your FAAC model from the plate and measurements, then match the correct bracket, yoke or plate, using genuine FAAC hardware where it matters and quality equivalents where they hold up. We carry no parts on a truck and claim no local stock, so the right part gets ordered and fitted, not improvised. Call (866) 623-9848 for a free estimate.
Beyond FAAC, we also service LiftMaster, Mighty Mule and Ghost Controls, so whatever is on your Summerlin driveway, we can help. Call (866) 623-9848 for a free estimate today.
Written by the team at Ironworks Gate Co. Summerlin, serving Summerlin and nearby areas.