Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateBFT Access Control Installation: The Summerlin Owner’s Guide
We install BFT-compatible access control equipment for Summerlin homeowners, and most installations land between $650 and $1,850 depending on how many entry points and credentials are involved. Repair calls on keypads, readers, and control boards that have already failed are often scheduled same-day. Owners usually discover the problem at the worst possible moment: the keypad beeps but the gate stays shut, the remote stops working, or a visitor sits stuck at the call box while the house phone rings unanswered. The gate was working fine last week. Now it’s not, and you’re standing in the driveway wondering whether it’s the battery, the board, or the whole unit. We hear that same story across Summerlin several times a month.

Which BFT Models This Applies To
BFT makes the access control hardware in two broad families: the keypad and reader units that sit on a pedestal or post (the QSC, Compact, and Clonix lines), and the control boards and receivers inside the operator housing (the LIBRA, DEIMOS, and ARES series of swing and slide operators). The access control side often connects to whichever of those operators you own, so the replacement part has to match both.
The single biggest compatibility gotcha with BFT is the receiver frequency. Older BFT Clonix receivers run on 433 MHz, while some newer units and the Mitto series use rolling-code 433.92 MHz, and the two are not interchangeable even though they look identical on the outside. We’ve seen Summerlin owners order the wrong receiver twice in a row because the listing said “BFT compatible” without specifying the frequency and code type. Check the label inside the receiver housing before you order anything. If the part number ends in a code you don’t recognize, bring us a photo.
On the OEM-vs-aftermarket question: we use genuine BFT parts when the originals are available and a quality equivalent when they aren’t, and we tell you which one you’re getting before we order. BFT discontinued several older Clonix receivers years ago, and the replacement path is a newer unit that requires a small wiring change. We do that regularly.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your BFT Access Control Installation Is Failing
- Keypad accepts the code but the gate won’t move. Usually the keypad is fine and the control board relay has failed, or the wiring between the keypad and operator has a broken connection at a wire nut.
- Remote works from ten feet but not thirty. This is usually the receiver losing sensitivity or a failing antenna connection, not the battery in the remote. Swapping the remote battery first is a common and costly mistake.
- Gate opens for one visitor and ignores the next. On BFT Clonix systems, an intermittent response usually points to the receiver memory holding a partial code, or a control board that is getting heat-soaked inside the housing.
- Call box rings the house phone but the gate won’t release. The telecom side and the access side are two separate circuits, and the fault is almost always on the access side relay, not the phone line.
- Unit acts dead in the afternoon but works at night. Summerlin’s summer heat pushes interior housing temperatures well past 120°F, and aging control boards and receivers fail on heat before they fail outright. This pattern is common here and rare in cooler climates.
Replacement Cost & What’s Included
Installed access control work in Summerlin typically runs:
| Work | Typical Installed Range |
|---|---|
| Keypad replacement (single entry, BFT-compatible) | $280 – $480 |
| Receiver replacement (Clonix or Mitto equivalent) | $220 – $400 |
| Control board replacement | $380 – $720 |
| New access control installation (keypad, reader, wiring) | $650 – $1,850 |
| Multi-entry or telephone entry integration | $1,200 – $3,200 |
Most Summerlin jobs fall in the middle of these ranges. What pushes a job up: aging wiring that has to be replaced rather than reused, a discontinued unit that needs a newer replacement with adaptation, or a gate with two entry points. What keeps a job low: a clean one-for-one swap with wiring in good condition.
We quote the full price before we turn a bolt, and the number we quote is the number on the bill. Every install is covered by our 90-Day Done Right Promise in writing: if it’s not right, we come back and make it right.

See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Some things are safe to check yourself: swap the remote battery, look for corrosion or insect nests in the keypad, and confirm the circuit breaker to the operator hasn’t tripped. That’s where DIY should stop.
Access control work crosses wiring, low-voltage circuits, and the operator’s safety edges – and getting it wrong can leave the gate operating with a disabled reversal sensor, which is a genuine hazard. Wires carrying 24V or line voltage run inside the same housing, and a wrong connection can fry the control board or back-feed into the keypad. We’ve replaced more boards ruined by DIY attempts than we can count, and that’s a conversation we’d rather not have after the fact. If the gate has stopped responding and you’ve ruled out the breaker and the remote battery, call us at (866) 623-9848. A live person answers, day or night.
FAQs
How long does a BFT access control installation last in Summerlin? A properly installed BFT-compatible unit typically gives eight to twelve years in Summerlin, shorter than in cooler climates because of heat exposure. Units mounted where the housing sits in full afternoon sun tend to fail sooner. Shade, ventilation and a clean install all buy extra years.
Can a failing BFT part be repaired instead of replaced? Sometimes, yes – a receiver antenna, a wire nut, or a corroded terminal can often be repaired for a fraction of replacement cost. Control boards and keypad logic circuits are usually not economically repairable. We diagnose first and tell you which side of that line you’re on before quoting. Call (866) 623-9848 for a free second opinion on any written estimate.
How long does the swap take? Most single-entry swaps finish in two to three hours. Multi-entry integration or a discontinued-unit replacement with wiring adaptation takes a full morning or afternoon. We measure and schedule installations in advance so the work is done correctly, not quickly. Free estimate, upfront price, no surprises.
How do you source BFT parts? We use genuine BFT parts when current stock is available and quality equivalents when BFT has discontinued the part, and we tell you which option you’re getting before we order. We don’t carry parts on a truck; each job is sourced for your specific model. Ironworks Gate Co. Summerlin is an independent service provider and is not affiliated with BFT. We also service LiftMaster, Mighty Mule, and Ghost Controls for nearby neighbors.
Call Ironworks Gate Co. Summerlin
If your BFT keypad, receiver, or control board has stopped doing its job, we’re the company to call. Live person on the line 24 hours a day, seven days a week, at (866) 623-9848. Free estimates, upfront pricing agreed before any work starts, and our 90-Day Done Right Promise on every job. Standing offers: $50 off any repair over $250, free second opinion on any written estimate, $89 seasonal tune-up, and a 5% senior and veteran discount. Our technicians have up to 13 years of experience, and we stand behind every job. Call (866) 623-9848 for your free estimate.
Written by the team at Ironworks Gate Co. Summerlin, serving Summerlin and nearby areas.