A Ironworks company - serving Summerlin, NV

Viking Gate Motor Replacement in Summerlin, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Viking Gate Motor Replacement: The Summerlin Owner’s Guide

We replace Viking gate motors for Summerlin homeowners, and a typical installed replacement runs $650 to $1,400 depending on the model and whether the operator board, arm, or full motor assembly is being swapped. Viking accessories and common arm replacements can often be handled same-day; full motor and board replacements are usually scheduled within a few days once we confirm the exact model. You’ll usually find out something is wrong the same way our Summerlin customers do: the gate stops halfway and reverses, the arm groans through the first few feet, or the opener clicks but nothing moves. Viking units are solid, so when one acts up in Summerlin’s heat, it’s almost always a worn arm, a tired control board, or a motor that’s been cooking in an unshaded enclosure for a decade.

professional gate repair service in Summerlin, NV

Call (866) 623-9848

Which Viking Models This Applies To

Viking Access Systems builds primarily swing gate operators, and the models we see on Summerlin driveways are the K-2, K-4, L-3, and the older B-12 and G-5 lines, along with the various arm and control board revisions that changed across production runs. The model plate is usually on the operator housing, and if the label is sun-bleached (common in Summerlin after 10 or 15 years), the arm casting, control board layout, and limit-switch style will tell us which revision you have.

Here’s where Viking gets tricky: the same model name was sold with different control board revisions over the years, and a board from one revision will not drop into another without the matching harness and limit setup. That’s the compatibility gotcha that bites online buyers. We match by board part number and arm casting, not just by the model name on the housing. On the OEM-versus-aftermarket question, we use OEM Viking boards and arms when they’re available and a quality aftermarket equivalent when OEM is discontinued or back-ordered for weeks, and we tell you which one you’re getting before we order. Ironworks Gate Co. Summerlin is an independent service provider and is not affiliated with Viking.

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Signs Your Viking Gate Motor Replacement Is Failing

  • The gate reverses mid-travel. The control board is reading a false obstruction, usually from a failing limit switch or a board that’s been heat-stressed. In Summerlin, a motor housing in direct afternoon sun accelerates this.
  • The arm groans or shudders through the first few feet. A worn arm bushing or a motor with tired brushes. If it smooths out once moving, the motor is on its way out rather than dead.
  • The opener clicks but the gate doesn’t move. A dead motor winding or a failed start capacitor on the board. This is a motor or board replacement, not an adjustment.
  • The gate drifts or won’t hold position. A failing encoder or limit switch that’s lost its reference. Sometimes repairable, often a sign the board is aging out.
  • Repeated tripping of the breaker or a dead operator after a power surge. Summer monsoon season in Summerlin brings surges that take out control boards. If the board is fried, the motor may still be good and only the board needs replacing.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Installed Viking gate motor replacement in Summerlin runs about $650 to $1,400. Board-only replacements land on the lower end, arm replacements in the middle, and full motor-and-board swaps on the higher end. The range is driven by the model, whether OEM or aftermarket parts are used, and whether the existing wiring and limit setup can be reused. We quote parts and labor separately, so you see exactly what the Viking part costs and what installation costs. The price is quoted and agreed before a single bolt is turned, and every job is backed by our written 90-Day Done Right Promise. Eligible repairs over $250 qualify for $50 off, and we offer a free second opinion on any written estimate.

DIY or Call Us?

You can safely check the model plate, confirm the gate swings freely by hand with the operator disengaged, and reset the breaker once. Anything past that, especially opening the operator housing to reach the control board or motor, is where DIY goes wrong on a Viking unit. Gate motors run on 120V line power, the arm is under load, and a miswired board can damage the motor or create a shock hazard. The honest line: checking symptoms is fine, replacing the motor or board is a job for a technician. Our technicians have up to 13 years of experience and are trained on Viking alongside LiftMaster, Mighty Mule, and Ghost Controls. Call (866) 623-9848 and we’ll get you a square deal and a straight answer.

FAQs

How long does a Viking gate motor last in Summerlin? A Viking motor typically lasts 10 to 15 years in Summerlin, though direct sun exposure and monsoon-season power surges can shorten that to 7 or 8 years. Shade and a surge protector make a real difference.

Can my Viking motor be repaired instead of replaced? Often yes. A failed board, limit switch, or capacitor can be replaced without touching the motor, which costs less. We diagnose first and only recommend a full replacement when the motor itself is failing.

How long does the replacement take? A board or arm swap is usually a single visit of one to two hours. A full motor replacement typically takes two to four hours, and we confirm the exact model and parts before scheduling.

How do you source the Viking part? We match by board part number and arm casting to your exact revision, then source OEM Viking parts when available or a quality aftermarket equivalent when OEM is discontinued. We tell you which one before we order, and the price is set before work starts. Call (866) 623-9848 for a free estimate.

Written by the team at Ironworks Gate Co. Summerlin, serving Summerlin and nearby areas.

Need Gate Repair help nationwide? Licensed & insured · 60-minute response · free estimates
Call (866) 623-9848
Local Service Coverage

Request a Free Estimate in Summerlin

Tell us what you need - Ironworks Gate Co. Summerlin responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Call Now - 24/7 Dispatch