Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateViking Hinge & Roller Replacement: The Summerlin Owner’s Guide
We replace failed and failing Viking hinges and rollers with Viking-compatible parts. Installed cost in Summerlin typically runs $145 to $320 per hinge-and-roller set, and most single-set replacements are done same day when you call before early afternoon. We’re an independent service provider, not affiliated with Viking, and we source parts matched to your exact model.

Owners usually find the problem the same way. The gate starts to sag at the latch side, and the latch no longer lines up without lifting. Or the gate drags across the pavers through the middle of its swing, leaving a bright scrape mark. Some hear a grind or a creak that wasn’t there last month. In Summerlin, that creak often shows up in late spring and early fall, when the temperature swings bring out a hinge that’s been dry or worn for a while. A roller with a flat spot or a hinge pin with worn bushings won’t fix itself, and a dragging gate puts strain on the motor every time it opens. Call (866) 623-9848 and we’ll take a look.
Which Viking Models This Applies To
Viking builds several gate operator families, and the hinge and roller hardware that mounts to the gate leaf varies by series. The most common residential setups in Summerlin use swing operators where the gate hangs on two or three hinges, and the roller or guide hardware depends on whether the gate swings or slides. What matters most is measuring, not guessing. We check the hinge’s pin diameter, the plate bolt pattern, and the roller’s wheel diameter and bore before we order anything.
Viking models share parts families across their swing and slide lines, but the exact hinge size and roller spec can change between series. If your gate has a maker’s label, the model and serial number are usually stamped on a plate on the operator housing or inside the control box. If the label is gone, we measure instead. That’s routine.
On the OEM-versus-aftermarket question, we’re straight with you. Viking-branded hinges and rollers are the safest fit when your gate is newer or still under warranty. For older gates where the exact OEM part is hard to get or overpriced, a matched aftermarket hinge with the same pin diameter and bolt pattern does the job. We tell you which one we’re recommending and why, and you decide. We don’t claim to stock parts or carry them on a truck. What we do is identify the right part, order it, and install it correctly the first time.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Viking Hinge & Roller Replacement Is Failing
Here’s what a failing hinge or roller looks like, and what’s actually going on underneath.
- The gate sags and the latch won’t line up. A worn hinge bushing or a bent hinge pin lets the gate drop at the free end. If you have to lift the gate to close it, the hinge is the usual cause.
- The gate drags or scrapes along its path. A flattened roller wheel or a seized roller bearing keeps the gate from riding smoothly. The scrape mark on the pavers or driveway is your clue.
- Grinding, squealing, or a heavy creak during movement. Dry or worn hinge pins and rollers make noise. In Summerlin’s heat and dry air, grease dries out faster than owners expect.
- The gate feels loose or wobbly when you push it. Worn hinge plates or elongated bolt holes let the gate shift. Left alone, that wobble works the whole hinge loose.
- The motor strains or the operator cuts out mid-travel. When a hinge or roller binds, the opener works harder to move the gate. That strain shows up as hesitation, stalling, or repeated safety reversals.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed hinge and roller replacement in Summerlin runs about $145 to $320 for a typical set, and most single-set jobs are completed same day. Here’s what drives the range:

- Number of hinges and rollers: a two-hinge gate is at the low end; a taller gate with three hinges and a roller or guide set runs higher.
- OEM versus matched aftermarket: OEM parts cost more than a quality equivalent with the same specs.
- Gate weight and condition: a heavy or out-of-alignment gate takes more time to hang and adjust correctly.
Every price is quoted and agreed before a single bolt is turned, so there are no surprises on the bill. We also honor $50 Off Any Repair Over $250 and a permanent 5% Senior and Veteran discount. Our work is backed by the written 90-Day Done Right Promise, the Keystone Standard: if it isn’t right, we come back and make it right. A square deal, backed in writing.
DIY or Call Us?
Some checks are safe for an owner. You can look at the gate’s swing, note where it drags, feel for wobble at the hinges, and listen for grinding. You can also read the model and serial number off the operator label. That’s useful information to have when you call.
Replacing hinges and rollers is a different matter. It means supporting the full weight of a gate, and a heavy driveway gate can weigh hundreds of pounds. Letting one down wrong, or getting a finger under a pinch point, causes real injuries. A gate that comes off its hinges can also fall. Beyond safety, getting the alignment wrong puts extra strain on the Viking operator and shortens its life. This is work for someone trained and equipped to do it safely. Our technicians have up to 13 years of experience, and we’re trained on Viking among nine gate-automation brands. Call (866) 623-9848 and we’ll get it right.
FAQs
Most gate hinges and rollers last eight to fifteen years depending on use and maintenance. In Summerlin, hot, dry summers dry out grease faster, and gates that sit in full afternoon sun tend to wear sooner. Keeping pins and rollers greased extends the life considerably.
Sometimes. A hinge that’s simply dry can be greased and adjusted; a roller that’s loose can be re-tightened. But a worn bushing, a bent pin, or a flattened roller wheel has failed and needs replacement. We assess honestly and tell you which one you’re dealing with. Call (866) 623-9848 for a free estimate.
A typical hinge and roller set replacement takes about one to two hours, and most jobs are done in a single visit. We line up the gate, adjust the swing, and test it before we leave. Call (866) 623-9848 to schedule.
We identify your Viking model and measure the hinge pin diameter, plate bolt pattern, and roller specs to match the exact part. If the label is missing, we measure everything and order the correct match. We order the part for your gate rather than guessing at a universal fit. Call (866) 623-9848 for an exact quote, and estimates are free.
When a Viking hinge or roller fails, you want it matched right, installed fast, and backed in writing. Ironworks Gate Co. Summerlin services Viking alongside LiftMaster, Mighty Mule, and Ghost Controls, and our technicians have up to 13 years of experience. We make 40-year-old gates close like the day they were hung. Call (866) 623-9848 for a free estimate, ask about our $89 Seasonal Tune-Up, and get your gate swinging true again.
Written by the team at Ironworks Gate Co. Summerlin, serving Summerlin and nearby areas.