Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Access Control Installation: The Summerlin Owner’s Guide
We install Ghost Controls-compatible access control – keypads, telephone entry, vehicle sensors, and the low-voltage wiring that ties them to your operator – and most Summerlin jobs land between $385 and $950 installed, depending on how many entry points and what’s already wired. Same-day service is often possible when you call before midday. Owners usually find the failure the same way: the keypad beeps but won’t accept the code, the gate stops responding to the remote at the top of the driveway, or the intercom crackles and nobody can buzz in. One morning the gate simply ignores everyone.

We’re an independent service provider, not affiliated with Ghost Controls. What we are is trained on the brand, and we’ve replaced enough of these units around Summerlin to know which failure you’re looking at before we open the housing.
Which Ghost Controls Models This Applies To
Ghost Controls builds around a handful of operator families – the single-swing AX and AR series, the dual-swing TDS and TSS lines, and the slide and solar variants. The access control side is where the confusion starts. The accessory keypad and entry units are not universal across every series: the low-voltage terminal layout and the control-board connector differ between the older three-terminal boards and the newer plug-in boards. If you order the wrong one, it will bolt up fine and simply not talk to the operator.
Identify your unit before ordering anything. Look for the model plate on the underside of the operator housing or inside the control box lid – it carries the full series number, not just “Ghost Controls.” If the plate is sun-bleached, photograph the control board and we can read the terminal count and connector style from it. That board photo is the single most useful thing you can hand us.
On the OEM-versus-aftermarket question: for keypads and entry units, we lean OEM or a known-equivalent because the firmware handshake with the board matters, and a cheap clone will often pair once and then drop codes. For wire, conduit, and mounting hardware, quality aftermarket is fine and saves you money. We’ll tell you which side of that line each part falls on before you commit.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Ghost Controls Access Control Installation Is Failing
These are the failures we see most on Summerlin gates, and what’s usually behind each one.
- The keypad accepts the code but the gate doesn’t move. The keypad is fine; the signal isn’t reaching the board. Usually a corroded terminal at the operator or a wire that’s cracked where it exits the post – Summerlin’s summer heat bakes exposed low-voltage wire until the jacket splits.
- The entry unit works intermittently. Power or a loose common connection. Desert temperature swings work terminals loose over a few seasons, and a connection that tests fine in the cool of morning can fail by 2 PM.
- The remote works from the driveway but not from the street. Range loss points to an antenna or receiver issue on the access control side, not the operator itself. Sometimes it’s as simple as a wire pinched in the housing.
- The gate opens on its own. A stuck or moisture-fouled button on the keypad, or a short in buried wire. This is the one to call on promptly – an unattended gate cycling open is a real security gap.
- Solar-powered units go dead by evening. The panel or battery is failing to hold charge, which knocks out the access control before it knocks out the gate. Common on shaded Summerlin lots where the panel never gets full sun.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing for Summerlin runs roughly $385 to $950. A straight keypad swap on an existing wired post sits at the low end. A full entry-unit replacement with new low-voltage run, conduit, and board integration sits at the high end. Solar accessory work and multi-point entries push toward the top.
What drives the range: the number of entry points, whether wire and conduit already exist and are sound, and whether the control board needs a connector adapter. We quote the whole job upfront, and that price is settled before a single bolt is turned – no surprises on the bill when we hand you the invoice.

| Scope | Typical Installed Range |
|---|---|
| Keypad replacement, existing wiring | $385 – $520 |
| Entry/intercom unit with board integration | $520 – $740 |
| New low-voltage run, conduit, and unit | $740 – $950 |
Every job is covered by our written 90-Day Done Right Promise – if it isn’t right, we come back and make it right.
DIY or Call Us?
There’s a safe middle ground here. You can check the obvious: confirm the operator has power, look for a tripped breaker, and photograph the model plate and control board. That’s genuinely useful and costs nothing.
Where DIY goes wrong is the low-voltage wiring and the board itself. Ghost Controls boards run on low voltage, but they’re tied to a line-powered operator, and reaching into a control box that shares a circuit with a 120-volt supply is where homeowners get hurt. Miswiring the accessory terminals can also cook the control board – a part that costs more than the keypad you were trying to replace. We’d rather you stop at the photograph. Call (866) 623-9848 and we’ll tell you what you’re looking at, and whether it’s a swap or something more.
FAQs
Expect roughly 8 to 12 years for a keypad or entry unit here, shorter on full-sun west-facing posts. Summerlin’s UV load and 100-plus-degree summers dry out gaskets and fade displays faster than in milder climates, so a unit that’s spent a decade in direct sun is often near the end of its service life even if it still works.
Often, yes. Corroded terminals, cracked wire, loose commons, and pinched antenna leads are all repairs, not replacements, and they’re the most common causes we find. We diagnose before we quote, so you’re not paying for a new unit when a terminal cleaning and a wire repair will do.
A straight keypad replacement is usually an hour or two. If we’re running new wire and conduit, plan on most of a morning. We’ll give you a realistic window when we quote, and we’ll be there when we say.
We match the exact series from your model plate or board photo and order the correct OEM-compatible unit, then install and pair it to your operator on arrival. We don’t guess at the model – the wrong board connector is the most avoidable mistake on this job, and we’ve seen it happen when someone ordered by photo of the outside housing alone.
We also service LiftMaster, Mighty Mule, and DoorKing access control when your gate isn’t Ghost Controls. Call (866) 623-9848 for a free estimate, and a live person will answer, any hour.
Written by the team at Ironworks Gate Co. Summerlin, serving Summerlin and nearby areas.