Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateElite Gate Installation in Summerlin: What to Know First
Elite gate installation in Summerlin is measured, ordered and scheduled work, not a same-day dispatch – most full installations run one to three weeks from the free measure to the finished gate, depending on whether it’s a swing, sliding or double gate and whether the operator is going in at the same time. Budget roughly $2,400 to $6,800 for a driveway swing gate with an Elite operator installed, and expect the written price to be settled before a single hinge is welded or a post is set. We’re an independent Elite service provider, so nothing on this page comes from Elite itself.

This page is for the homeowner with an Elite keypad, Elite operator or an Elite gate plan who wants the job done once and guaranteed in writing – the kind of customer who picks up the phone rather than fills out a form. Call (866) 623-9848 and a live person answers, day or night.
How Elite Products Fail – and How We Fix Them
Elite equipment is solid when it’s set up for the gate it’s actually mounted on. Most of the Elite problems we see in Summerlin aren’t brand defects – they’re install and setup problems that surface months later. Here’s what shows up on our service calls.
- Operators sized for a lighter gate than the one hung on the posts. We regularly see an Elite swing operator installed on a gate that gained weight when the wood facing was replaced years later. The motor strains on every open, the arms wear early, and the control board throws a fault that looks electrical but isn’t. Our fix: weigh the gate, confirm the operator’s rated capacity, and either re-spring the geometry or upgrade the operator.
- Control-board damage from Summerlin heat inside a metal housing. A closed steel operator housing in direct summer sun can run dramatically hotter than the air temperature, and the charge controller and capacitor bank take the worst of it. Owners describe a gate that works in the morning and stalls in late afternoon. We relocate or shade the housing where we can and replace the board with the OEM part rather than a generic substitute.
- Limit switches drifting out of adjustment. A swing gate that stops a few inches short, or reverses halfway, is usually a limit-switch setting that shifted after a hard wind or a post settling. That’s a calibration on the Elite operator, not a new motherboard – we set the limits and re-test the reversal before recommending any part.
- Aftermarket battery and photo-eye substitutions that don’t hold. Cheap third-party batteries and safety photo-eyes are the most common reason an Elite gate becomes unreliable after someone else’s repair. We fit OEM or OEM-spec batteries and Elite-compatible safety edges so the operator’s own diagnostics read true. This is also the point where we check the power run and the safety edges – both must be right before the gate is ever signed off.
- Undersized or corroded posts behind a gate that “won’t stay aligned.” On older Summerlin properties, the real problem is often the gate frame and hinge posts, not the Elite hardware bolted to them. We check post depth, hinge condition and frame squareness first, because a new operator on a sagging frame will fail the same way.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Elite Gate Installation Process
- 1
Phone call and intake. You reach a live person, not a voicemail. We talk through the gate, the driveway, the operator you’re considering and what the gate needs to do – daily vehicle access, pedestrian entry, or both.
- 2
Free on-site measure. We measure the opening, confirm grade and swing clearance, check the post condition and look at the power location. For sliding and double gates this is where we answer the questions that decide the whole job.
- 3
Written price before any work. The estimate covers the gate, the Elite operator, the power run, the safety edges and the labor as line items. Nothing gets ordered until you approve it, and the price you approve is the price on the bill.
- 4
Installation to the Elite spec. Posts set and hinges aligned, gate hung and squared, operator mounted at the correct geometry, power run done to code, and safety photo-eyes and edges placed to match the Elite operator’s requirements.
- 5
Full test and walkthrough. We cycle the gate many times, test reversal and obstruction response, and show you the manual release and the keypad operation before we clean up and leave.
- 6
Guaranteed in writing. Every job is covered by our 90-Day Done Right Promise – if it isn’t right, we come back and make it right, no paperwork and no arguing.
See the difference
Before
After
Before
After
Before
AfterWhat Elite Gate Installation Costs in Summerlin
These are typical Summerlin ranges for Elite gate installation, and they move with gate size, material, operator model and how far the power has to run.
| Job | Typical range |
|---|---|
| Pedestrian swing gate, Elite operator | $1,600 – $3,400 |
| Single driveway swing gate, Elite operator | $2,400 – $4,800 |
| Double driveway gate, Elite operator | $4,200 – $7,900 |
| Sliding gate, Elite operator | $3,800 – $8,200 |
| Elite operator retrofit on an existing gate | $1,300 – $2,900 |
| New power run and safety edges | $450 – $1,600 |
What moves the price: gate weight and material, whether new posts are needed, the length and difficulty of the power run, and whether you need vehicle access control on the Elite keypad. If you have a written estimate from another company, we’ll give you a free second opinion on it. The price is quoted and agreed before any work starts. Call (866) 623-9848 for a free estimate.
Why Summerlin Homeowners Call Ironworks Gate Co. Summerlin for Elite Work
The company behind this page is Ironworks Gate Co., and we’ve been at this work in the area for over 42 years. Our technicians have up to 13 years of experience, and they’re trained on nine gate-automation brands – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule – so when the job is an Elite install with a LiftMaster component in the mix, they’re not guessing. Every technician is background-checked and uniformed, working in your home the way they’d work in their own mother’s. Our technicians are the ones who make the diagnosis and set the price before any work begins.

A live person answers the phone 24 hours a day, 7 days a week. We stand behind every job with the written 90-Day Done Right Promise. Active offers: $50 off any repair over $250, a free second opinion on any written estimate, an $89 seasonal tune-up, and a permanent 5% senior and veteran discount.
FAQs
Elite gate installation in Summerlin typically runs $1,600 to $8,200 depending on gate type and operator. The line-item range above covers a pedestrian gate up to a sliding gate, and a new power run adds $450 to $1,600. Call (866) 623-9848 for an exact quote – estimates are free.
Yes. The power run and the safety photo-eyes and edges are part of a proper Elite installation, and we include them as line items in the written price. We won’t sign off a gate without working safety devices – they’re a genuine safety matter, not an add-on. Call (866) 623-9848 to talk through your setup.
A full Elite installation includes the hinge and frame work, the operator mounted to Elite’s geometry spec, the power run, the safety edges and photo-eyes, a keypad if you want vehicle access control, and a full cycle test with a walkthrough of the manual release. The price is quoted and agreed before any work starts. Call (866) 623-9848 to schedule the free measure.
Repair is usually the right call when the gate frame and posts are sound and the fault is a limit setting, a board or a battery – many of those jobs are done in a single visit. Replacement makes sense when the operator is undersized for the gate or the board has failed twice in a season. Call (866) 623-9848 with the model and we’ll talk it through.
Most Elite gate installations in Summerlin are scheduled one to three weeks out, because the work is measured and ordered rather than dispatched. Emergency gate failures are a different matter – call (866) 623-9848 and a live person will help you any hour.
Written by the team at Ironworks Gate Co. Summerlin, serving Summerlin and nearby areas.