A Ironworks company - serving Summerlin, NV

Elite Gate Parts & Welding in Summerlin, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Elite Gate Parts & Welding in Summerlin: What to Know First

We provide independent Elite gate parts and welding in Summerlin, and most jobs are finished in a single visit. Common repairs – hinge replacement, post replacement, rail repair, custom welding, gate rollers, latch and lock work – typically run $180 to $850 depending on parts and whether we’re welding in place. The price is quoted and agreed before any work starts, so the invoice matches the number you were given.

Professional welder using an angle grinder for metal gate repair services in Summerlin, NV

Call (866) 623-9848

This page is for Summerlin homeowners with an Elite gate on the driveway who need it to swing and latch correctly again. We handle Elite hardware, operators, and the structural work around them. If that’s you, call (866) 623-9848 and a live person will pick up, day or night.

How Elite Products Fail – and How We Fix Them

Elite gear is well built, but every gate shows its weak points after enough summers in the Las Vegas Valley. Here’s what we actually see on Elite jobs in Summerlin, and how we handle each one.

  • Weld fatigue at hinge points. On heavier single-swing Elite gates, the hinge-side weld takes the full weight of the leaf every time it moves. After years of daily cycling, that weld cracks start to open along the post plate. We cut the old weld clean, re-plate if the steel is thin, and run a full-penetration weld so the joint holds. This is a structural fix, not a touch-up.
  • Sagging leaf from post movement. Summerlin sits on expansive clay soils, and the desert’s wet-dry swing moves posts more than most homeowners expect. When the post shifts, the gate drags, the opener strains, and eventually the hinge plates warp. We reset or replace the post in concrete, then rehang the leaf square. A post replacement often solves what looked like an opener problem.
  • Rail rust and pitting. Even powder-coated Elite rails pit where water sits in the bottom channel after monsoon season. Pitting turns to thin steel, and thin steel fails. We cut out the compromised section and weld in matching rail, then prime and refinish the repair so it blends with the rest of the gate.
  • Worn rollers and latches. Sliding Elite gates ride on rollers that flatten and bind with age; swing gates wear their latch and lock hardware until the gate closes but won’t secure. We replace rollers, tracks, and latch assemblies with correct-fit parts so the gate travels smooth and latches solid.
  • Opener strain from a heavy or misaligned leaf. An Elite operator is only as good as the gate it moves. When hinges bind or a leaf sags, the motor works harder than it should, and the control board or gearbox gives out early. We fix the gate geometry first, then confirm the operator is running within its limits before we call the job done.
Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Our Elite Gate Parts & Welding Process

A real Elite job follows the same order every time, so nothing gets skipped and nothing surprises you.

  1. 1
    Diagnose on site. We test the gate by hand and under power, check hinge and post condition, and find the true cause – not just the loudest symptom. You hear what’s wrong in plain terms before we quote.
  2. 2
    Parts decision. On Elite hardware, we weigh OEM parts against quality aftermarket. Where OEM matters for fit and warranty, we say so. Where an aftermarket part is equal and less costly, we say that too. You choose with the facts in front of you.
  3. 3
    Upfront price. The full scope and cost are written down and agreed before a single bolt is turned. No surprises on the bill.
  4. 4
    The repair. Welding, post work, hinge and rail repair, parts replacement – done by background-checked, uniformed technicians who treat your property the way they’d treat their own mother’s.
  5. 5
    Test and adjust. We cycle the gate under power, check alignment, latch, and safety, and make sure the operator isn’t straining. Then we clean up the site and walk you through what changed.
  6. 6
    Back it in writing. Every job carries our 90-Day Done Right Promise: if it’s not right, we come back and make it right.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

What Elite Gate Parts & Welding Costs in Summerlin

Prices vary with parts and access, but here’s what Summerlin homeowners typically see on Elite gate parts and welding work.

  • Hinge replacement: $180 to $340 per hinge set, welded and aligned.
  • Gate rollers: $150 to $320, including track check.
  • Latch and lock hardware: $160 to $400 depending on the assembly.
  • Rail repair / custom welding: $250 to $650, based on the length of rail and finish work.
  • Post replacement: $450 to $850, including concrete and rehang.

What moves the price: gate weight and size, whether we’re welding in place or on a bench, access to the post, and OEM versus aftermarket parts. Estimates are free, and we offer $50 off any repair over $250. Call (866) 623-9848 for an exact quote.

Professional welder using an angle grinder for metal gate repair services in Summerlin, NV

Why Summerlin Homeowners Call Ironworks Gate Co. Summerlin for Elite Work

We’re an independent Elite service provider – not affiliated with or authorized by the manufacturer – and we’ve built our reputation on getting the fix right the first time. Our technicians have up to 13 years of experience, and we’re trained and equipped on nine gate-automation brands, including LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so whatever’s on your driveway, the right fix gets made.

A live person answers every call, 24 hours a day, 7 days a week. No voicemail tree, no callback queue. Every job is protected by our written 90-Day Done Right Promise. We’re not the lowest bid – we’re the last call you’ll need to make on that gate. We also offer a free second opinion on any written estimate and a permanent 5% Senior and Veteran discount. We will be there when we say, and we stand behind it.

FAQs

Need Gate Repair help nationwide? Licensed & insured · 60-minute response · free estimates
Call (866) 623-9848
Local Service Coverage

Request a Free Estimate in Summerlin

Tell us what you need - Ironworks Gate Co. Summerlin responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Call Now - 24/7 Dispatch