Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateElite Access Control Installation: The Summerlin Owner’s Guide
Elite access control installation in Summerlin typically runs $650 to $1,900 installed, depending on whether you’re adding a single keypad or a full telephone entry and gate-operator interface, and most straightforward jobs are handled same day. When a call button, keypad, or intercom on an Elite system quits, owners usually find out the same way: the gate stops responding, or a visitor calls from the pedestal and gets nothing but dead air.

That dead pedestal is the moment this page is written for. It’s the button that used to buzz you through and now doesn’t. It’s the code that worked for years and suddenly triggers nothing. In Summerlin, we see a particular pattern with Elite units, and it usually traces back to the power supply or the pedestal wiring rather than the reader itself.
Which Elite Models This Applies To
Elite makes several access control and telephone entry lines, and the part you need depends on which one is on your pedestal. Most Summerlin homes with Elite equipment are running either the EL25 or EL2000 telephone entry series, or a standalone Elite keypad or card reader at a pedestrian gate. The model and serial label is almost always inside the pedestal door, on the back panel, or on the underside of the housing. Photograph it before you call anyone.
This is where the first compatibility gotcha lives. Elite telephone entry units and Elite access control accessories do not share mounting plates or wiring harnesses across series. An EL25 keypad assembly is not a drop-in for an EL2000, even though the faceplates look alike. Measure the pedestal cutout and note the harness connector type before ordering anything.
The OEM-versus-aftermarket decision for Elite is real. Elite-branded replacement boards and readers carry a premium and are the safest match for warranty continuity on a unit still under coverage. Quality aftermarket keypads and power supplies exist and are often fine for older systems where the original board is discontinued. We’ll tell you honestly which path your unit calls for. Ironworks Gate Co. Summerlin is an independent service provider and is not affiliated with Elite.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Elite Access Control Installation Is Failing
- The keypad lights but the gate won’t open. Power is reaching the pad, but the relay or the signal run to the operator has failed. That points to the control board or the low-voltage wiring, not the keypad face.
- Visitors call from the pedestal and get silence. On Elite telephone entry units, this is usually a failed interconnect board or a dead handset in the pedestal, both of which the afternoon sun and desert dust accelerate.
- Codes work intermittently, then stop. Intermittent behavior is the signature of a power supply on its way out or a corroded connector. It’s the most common Elite access control failure we see in Summerlin.
- The gate opens on its own or stays open. A stuck relay or a shorted control run can leave the operator commanded open. Treat this as a safety issue and get it looked at promptly.
- The reader reads cards or fobs but rejects known-good ones. The reader’s antenna or firmware has degraded, or the credential database has been lost. On older Elite boards, this is often the moment the board itself is the right replacement.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Summerlin, an Elite access control installation repair generally breaks down like this. A keypad or card reader replacement installed runs $220 to $480, depending on the reader and whether the pedestal wiring has to be re-pulled. A telephone entry board or interconnect replacement installed runs $350 to $780. A full power supply replacement installed runs $280 to $520. New pedestal wiring or a fresh low-voltage run adds $180 to $600, depending on distance and trenching.
What drives the range: whether the original unit is still serviceable, whether the pedestal wiring is sound or has to be re-run, and whether you’re matching an OEM Elite part or a compatible aftermarket equivalent. The price is quoted and agreed before any work starts, so the bill matches the estimate. Every access control install we do carries the written 90-Day Done Right Promise.
| Access control item (installed) | Typical Summerlin range |
|---|---|
| Keypad or card reader replacement | $220 – $480 |
| Telephone entry board or interconnect | $350 – $780 |
| Power supply replacement | $280 – $520 |
| New low-voltage wiring run | $180 – $600 |
| Full Elite pedestal unit replacement | $650 – $1,900 |
DIY or Call Us?
There are a few safe checks an owner can do. Confirm the pedestal has power at the breaker, look for a tripped GFCI, and check that the model label matches the part you’re considering. That’s it.
Here’s where DIY goes wrong. Access control pedestals carry line voltage feeding a low-voltage system, and mixing the two is how people get shocked or fry a board that was still good. On an Elite telephone entry unit, a miswired harness can cook the control board and turn a $350 repair into a $780 one. If you’re not certain which wire is which, stop. Call (866) 623-9848 and we’ll sort it out. A live person answers, day or night.
FAQs
How long does an Elite access control system last in Summerlin? Most Elite pedestal components last 8 to 12 years here, though direct-afternoon-sun pedestals on west-facing driveways often fail closer to 7. The desert heat and dust are harder on the power supply and readers than the control board.
Can a failing Elite access control part be repaired instead of replaced? Sometimes. Corroded connectors and re-seatable boards are often repairable, which is why we open the pedestal before quoting a full replacement. If the board is sound, we’ll repair it.
How long does the swap take? A keypad or reader replacement is usually a two-to-three-hour job. A telephone entry board or full pedestal replacement typically runs half a day. We’ll tell you up front.
How do you source the Elite part? We match the model and harness to the correct OEM or compatible aftermarket part, order it, and schedule the install once it’s in hand. We don’t carry parts on a truck.
Written by the team at Ironworks Gate Co. Summerlin, serving Summerlin and nearby areas.