Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateMighty Mule Welding & Fabrication: The Summerlin Owner’s Guide
We repair and fabricate Mighty Mule gate hardware in Summerlin, including cracked hinge brackets, worn pivot tubes, and fatigued arms on swing and slide operators. Most welding and fabrication jobs on a Mighty Mule gate run $220 to $540 installed, depending on whether we’re rebuilding an existing bracket or fabricating a replacement, and we can usually get to a gate that won’t close or has dropped on its hinges the same day you call. You’ll know it’s time when the gate sags at the latch, drags the ground at the strike post, or the operator arm starts binding halfway through its travel and stops.

Which Mighty Mule Models This Applies To
Mighty Mule builds its reputation on the DIY-friendly MM series: the MM260, MM360, MM560, and the older MM500 and MM600 lines, all sold through farm and ranch retailers and big-box stores. The welding and fabrication needs differ by generation. The older MM500/MM600 brackets are heavier plate steel and often outlast the gate itself; the newer MM260/MM360 brackets are stamped thinner and are the ones we see crack first at the mounting bolt holes. To match the right replacement, photograph the operator arm where it bolts to the gate, note the model number on the control box label (usually inside the housing), and measure the gate tube diameter at the hinge point. That measurement matters more than the model number, because Mighty Mule has used three different gate-tube sizes across the series.
On the OEM-versus-aftermarket question: Mighty Mule’s own replacement brackets are the safe match, but a properly fabricated bracket in the same gauge steel will outlast the original if the welds are right. We’re an independent service provider and not affiliated with Mighty Mule, so we give you the honest comparison rather than steering you to a brand. We also service LiftMaster, Ghost Controls, and DoorKing hardware.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Mighty Mule Welding & Fabrication Is Failing
Here in Summerlin, gate hardware takes a beating from the sun and the dry air, and the fatigue shows up in predictable places.
- The gate sags at the latch post. A cracked or bent hinge bracket has lost its square, and the gate tube is no longer riding true. You’ll see a gap at the top of the latch that wasn’t there last year.
- The operator arm binds or stalls mid-travel. The mounting bracket has flexed, throwing the arm out of alignment so the motor is fighting the geometry instead of the gate weight.
- Visible cracks at the bolt holes or weld seams. Look at the bracket where it attaches to the gate. Hairline cracks in stamped steel propagate fast, especially after a 110-degree Summerlin afternoon and a cool night.
- The gate drops or drags on the ground. A worn pivot tube or a fatigued weld at the hinge post lets the gate drop a half-inch, and that’s enough to grind the strike plate.
- Rattling or clunking when the gate moves. Loose or elongated bolt holes in a fatigued bracket, or a weld that’s cracked but hasn’t separated yet.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Every price we quote is settled before a single bolt is turned. Here’s what Summerlin homeowners typically see:
| Job | Installed Range |
|---|---|
| Repair existing hinge bracket (weld and reinforce) | $220 – $320 |
| Fabricate replacement mounting bracket | $280 – $420 |
| Rebuild gate frame at hinge point, operator arm included | $380 – $540 |
| Full gate re-square and weld-out | $450 – $700 |
What drives the range: whether we’re repairing existing steel or fabricating from scratch, the gauge and finish required, and whether the operator needs to come off the gate to do the work right. Every job is covered by our written 90-Day Done Right Promise: if it isn’t right, we come back and make it right, no paperwork, no arguing. We quote parts and labor together, so there’s no surprise line on the invoice. Active standing offers: $50 Off Any Repair Over $250, a Free Second Opinion on Any Written Estimate, and a permanent 5% Senior and Veteran discount.

DIY or Call Us?
Some checks are safe to do yourself. Walk the gate and look at the bracket where it meets the gate tube, wiggle the operator arm by hand with the power off, and note where it binds. If you can see a hairline crack or a bracket that’s visibly bent, that’s where we come in.
Welding on a live gate frame is where DIY goes wrong, and we say so plainly. You’re working next to a powered operator with stored tension in the arm, and a weld that isn’t structurally sound on a 200-pound gate is a genuine safety risk. A gate that drops while someone is walking through it can injure. That work belongs with a trained welder who can confirm the steel is sound and the geometry is true before anyone stands near it. If you’re unsure, call us at (866) 623-9848 and we’ll tell you straight.
FAQs
Stamped Mighty Mule brackets on the MM260 and MM360 lines typically hold 8 to 12 years in Summerlin’s climate, often less if the gate is on the west side of the house and gets full afternoon sun. Heat cycling from 110-degree days to 60-degree nights stresses weld seams and bolt holes faster than milder climates, so we often see fatigue cracks on gates that were fine for years and then fail in a single summer. Call (866) 623-9848 for an exact quote; estimates are free.
Usually yes. Most cracked Mighty Mule brackets can be welded and reinforced rather than replaced, which runs $220 to $320 installed and is often the right call when the original steel is sound. If the bracket has rusted through or the bolt holes are elongated, replacement is the better investment. We’ll tell you which before we touch the gate.
Most bracket repairs and fabrications are a single-visit job, typically two to three hours on site. If we’re fabricating a custom bracket from scratch, we may need to measure on the first visit and install on the second, and we’ll schedule that with you upfront. If the gate isn’t closing safely, call us and we’ll get eyes on it fast.
We fabricate brackets in-house to match your gate’s tube size and the operator’s mounting geometry, and we source OEM Mighty Mule parts when an original match is the right answer. Because we’re trained on nine gate-automation brands, we compare the OEM part against a properly welded equivalent and give you the honest call. No parts are carried on the truck; everything is measured and ordered to your gate. Call (866) 623-9848 for a free estimate.
If your Mighty Mule gate in Summerlin has a cracked bracket, a sagging hinge, or an operator arm that won’t track straight, give us a call at (866) 623-9848. A live person answers 24 hours a day, 7 days a week. We’ll give you a free estimate, an upfront price settled before we start, and work backed by our 90-Day Done Right Promise. Done right, and backed in writing.
Written by the team at Ironworks Gate Co. Summerlin, serving Summerlin and nearby areas.