A Ironworks company - serving Summerlin, NV

Before & After Gallery - Ironworks Gate Co. Summerlin

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Gate Repair Before & After in Summerlin, NV

Claims are cheap. A gate that swings level, latches clean and answers the keypad on the first try is the proof. Below is how Ironworks Gate Co. Summerlin approaches representative gate repair jobs across Summerlin – the problem, what we did, and what the homeowner got back. Photos drop into each frame as jobs are documented.

Call (866) 623-9848

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Recent Transformations

Driveway Gate That Wouldn’t Close Fully

BeforeBeforeAfterAfter
Before – sagging driveway gate, dragging on the latch side
BeforeBeforeAfterAfter
After – level swing, clean latch, corrected hinge and weld

The problem starts in the hinges and the posts, not the motor. A heavy wrought-iron leaf that has dropped a quarter-inch over a couple of seasons drags the strike plate, and the operator gets blamed for a job it never had a chance to finish. We re-hung the leaf, welded a fatigued hinge bracket and reset the closing travel. The gate closes under its own weight now and the operator cycles without strain. Done right – and backed in writing through the 90-Day Done Right Promise.

Sliding Gate Off Its Track

BeforeBeforeAfterAfter
Before – sliding gate jumped the track and jammed
professional gate repair service
After – replaced rollers, straightened track, smooth travel

A sliding gate that jumps the track usually means worn rollers and a track that has shifted at the anchor bolts. We replaced the roller carriers, straightened the track run and re-anchored the rail into sound concrete. The gate now travels its full span without a hitch, and the homeowner can open it by hand if the power ever goes out.

Gate Opener That Wouldn’t Respond to the Remote

Professional welder performing on-site wrought iron gate repair and maintenance.
Before – opener dead to every remote
Professional technician performing gate latch hardware repair and installation
After – receiver and limits reset, remotes working

The remotes weren’t the issue; the receiver and the limit switch settings were. We tested the control board, reset the limits and re-paired the homeowner’s remotes. Ironworks is trained on nine leading gate-automation brands, so the correct fix is made on the first visit – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite or Mighty Mule, we know the panel in front of us.

Keypad and Access Control Failure

Technicians installing a decorative metal gate with level and power drill
Before – keypad not reading codes, guests stuck outside
professional gate installation service
After – new keypad wired and tested, codes restored

An entry keypad that stops accepting codes leaves everyone waiting at the curb. We traced the fault to a corroded connection in the low-voltage run and a failing keypad unit. The connection was repaired, the keypad replaced and every code re-tested with the homeowner before we left. A square deal: the price was agreed before we touched the panel.

Weld Failure on an Older Estate Gate

Two professional contractors installing a new black metal gate.
Before – cracked weld at the frame corner
Technician repairing an electric gate motor circuit board with a multimeter
After – re-welded, ground clean and painted

A cracked weld at a frame corner is a structural problem, not a cosmetic one, and it can let a leaf fold under its own weight. We ground out the old weld, re-welded the joint properly and touched up the finish. The gate is solid again and the homeowner avoided a full replacement – the company that makes a 40-year-old gate close like the day it was hung.

Seasonal Tune-Up That Prevented a Breakdown

Technician performing professional maintenance on an automatic residential gate motor
Before – worn rollers and dry hinges caught in a tune-up
professional gate motor & opener service
After – lubricated, tightened and cycling cleanly

Our $89 Seasonal Tune-Up exists for exactly this: to catch worn rollers, loose bolts and dried hinges before they become a stuck gate in July. We serviced the hardware, lubricated the moving parts and confirmed the operator was cycling within its limits. Most jobs are completed in a single visit, with the price settled upfront before a single bolt is turned.

Want Results Like These?

If your gate is sagging, stuck, or ignoring the remote, call Ironworks Gate Co. Summerlin at (866) 623-9848. A live person answers 24 hours a day, background-checked technicians do the work, and the price is agreed before we start. Ask about $50 off any repair over $250 and our free second opinion on any written estimate.

Written by the team at Ironworks Gate Co. Summerlin.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade
Need Gate Repair help in Summerlin? Licensed & insured · 60-minute response · free estimates
Call (866) 623-9848
Local Service Coverage

Request a Free Estimate in Summerlin

Tell us what you need - Ironworks Gate Co. Summerlin responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Call Now - 24/7 Dispatch