Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateBFT Gate Installation in Summerlin: What to Know First
We install and replace BFT gate operators for Summerlin homeowners as an independent BFT service provider, and most standard driveway and swing gate installations are scheduled within one to two weeks of a free on-site measure. Gate automation is measured, ordered, and scheduled work, so we don’t promise same-day installs. What we do promise is a written price before a single bolt is turned. If you’ve got a BFT on the driveway, or you’re ready to put one in, call (866) 623-9848 for a free estimate.

This page is written for the homeowner who already knows the brand, wants the install handled by someone who knows the BFT line, and doesn’t want to explain their own equipment to a crew that mostly hangs LiftMaster openers. If that’s you, you’re in the right place.
How BFT Products Fail – and How We Fix Them
BFT gear is a serious product line, and the installs we see in Summerlin are usually solid from the factory. The failures tend to come from our desert conditions and from installations that were never quite right to begin with. These are the patterns our technicians run into most:
- BFT Deimos series: control board and encoder faults after summer heat. The Deimos BT is a workhorse for single swing gates, but the encoder and control board sit inside an enclosure that bakes during a Summerlin July. We see gates that open partway and stall, or reverse without warning, because the board is losing its position reference. The fix is usually a board or encoder swap with a proper shade cover, not a whole new operator. That board-versus-operator call is the expensive part if nobody diagnoses it correctly.
- BFT Phobos BT: worn rack and pinion after years of sun-baked cycles. The Phobos is a sliding-gate operator, and in Summerlin the drive pinion wears faster than the gate itself. Homeowners will tell us the gate “grinds” at the start. That’s the pinion climbing a tired rack, and left alone it strips teeth. We replace the rack section and pinion together, because replacing one and not the other just buys you six more months.
- BFT Ares and Icaro: battery backup that has quietly died. Both lines carry battery backup, which sounds like a comfort feature until a spring windstorm knocks out power in the middle of a Summerlin evening. A battery that has never been tested may be dead on arrival for the event you bought it for. We load-test the battery during install and replace it if it won’t hold.
- BFT Virgo and the pedestrian swing line: mis-set limit switches causing over-travel. We regularly find pedestrian gate operators installed with limits that let the gate slam against the stop on every cycle. That shortens the operator’s life and cracks welds at the hinge. The remedy is a limit reset and a softened deceleration profile, plus a hinge and post check while we’re there.
- Undersized footings and solar-heat-driven control faults. A BFT swing operator on a slab that was poured too thin will torque the post out of alignment within a couple of years, which throws the operator out of its operating geometry. When we install, we set the footing to spec for the gate weight and the operator. That single detail prevents most of the fault calls we get back on swing gates.
Why Summerlin Conditions Make BFT Failures Different
Summerlin sits at higher elevation than the valley floor, and the swing between a cool winter morning and a 115-degree July afternoon is hard on plastic parts, seals, and control boards. We use UV-rated covers and enclosures on every BFT install, and we size wire runs generously so the operator doesn’t strain through a long summer. Those two habits cost a little more up front and save a lot of truck rolls later.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our BFT Gate Installation Process
- 1
Phone call and free on-site measure. A live person answers the phone at any hour, so you’ll never leave a message. We come out, measure the opening, check the hinge posts and footing, and look at the power path and grade.
- 2
Written price before we start. We quote the operator, the accessories, the wiring, and any gate repair in writing. You agree to the price before a single bolt is turned. That’s the whole deal.
- 3
Parts decision, made plainly. We source OEM BFT parts when the operator calls for them and quality aftermarket when the OEM part is overkill. We explain the trade-off in plain English and let you decide. No surprises on the bill.
- 4
Installation and safety check. We set the footing to spec, mount the operator, wire the power run, and install safety edges, photo-eyes, and the test cycle. We test the gate through a full open/close cycle while you watch.
- 5
Walkthrough. We show you how to release the gate by hand during a power failure and how to test the battery backup. You’ll know your equipment when we leave.
- 6
The 90-Day Done Right Promise. Every job is backed in writing. If something isn’t right, we come back and make it right. No arguing, no paperwork, no exceptions.
Safety note: gate automation involves live wiring, high-torque motors, and a moving gate that can injure. We install and service this equipment as trained professionals, and we’d strongly caution against DIY on the electrical side or on the operator’s springs and stop mechanisms. Call us instead.
See the difference
Before
After
Before
After
Before
AfterWhat BFT Gate Installation Costs in Summerlin
Every job is measured and quoted in writing, and the price is agreed before any work starts. Here are the ranges we typically see:
| Installation Type | Typical Price Range |
|---|---|
| Single swing gate operator (BFT Deimos Ares) | $1,450 – $2,400 |
| Sliding gate operator (BFT Phobos) | $1,700 – $2,900 |
| Double swing gate installation | $2,600 – $4,600 |
| Pedestrian swing gate (BFT line) | $900 – $1,700 |
| Battery backup and safety edge add-on | $250 – $650 |
| Power run and access control integration | $400 – $1,200 |
What moves the price: gate weight and material, footing condition, run distance from the panel, and whether the gate needs welding or hinge repair before the operator goes on. We quote all of it up front. Call (866) 623-9848 for an exact price on your gates – estimates are free, and we’ll bring the discount on a full install with us.
Why Summerlin Homeowners Call Ironworks Gate Co. Summerlin for BFT Work
We’ve been doing this work locally for over 42 years, and the BFT line has been part of that work for most of it. Our technicians have up to 13 years of experience, are background-checked and uniformed, and know the operator on your driveway. We’re trained and equipped on nine gate-automation brands, including LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if your gate is a mixed setup or you’re not sure what you’re looking at, we can still make the right call.
Every job comes with the 90-Day Done Right Promise and a live person on the phone 24 hours a day, 7 days a week. If you want the square deal and the written price, call us. We will be there when we say.
FAQs
Yes. Every BFT installation we complete is backed by our 90-Day Done Right Promise in writing. If the operator or the install isn’t right, we come back and make it right. Call (866) 623-9848 for a free estimate.
In most cases, yes. We check the gate weight, hinge posts, footing, and grade before we commit. If the gate needs repair or hinge welding first, we tell you that up front and quote it in writing. Call (866) 623-9848 and we’ll set a free measure.
We source OEM BFT parts and quality aftermarket where it makes sense, and we’ll tell you which is which before you decide. Most installs go in with a single visit because we order correctly the first time. Call (866) 623-9848 and we’ll talk through your operator.
Sometimes a repair is the right call and sometimes a replacement is, and the answer depends on the operator’s condition, not the age on the label. We’ll tell you honestly which one makes sense, and we’ll quote both so you can decide. Call (866) 623-9848 for that second opinion.
Most standard driveway and swing installations are scheduled within one to two weeks of the free measure, and most single-operator jobs are completed in one visit once we arrive. This is measured and scheduled work, not dispatch. Call (866) 623-9848 to get on the schedule.
Written by the team at Ironworks Gate Co. Summerlin, serving Summerlin and nearby areas.