Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateDoorKing Access Control Installation: The Summerlin Owner’s Guide
DoorKing access control installation in Summerlin typically runs $650 to $2,400 installed, depending on whether you’re replacing a single keypad or a full entry system with telephone entry, card reader, and vehicle loop. Same-day service is available for failed entry systems, and every price is agreed in writing before we start. Most Summerlin owners discover the problem the same way: the gate opens for the departing car but won’t accept the return code, or the keypad beeps and does nothing while the entry panel shows a fault the manual doesn’t explain. Ironworks Gate Co. Summerlin is an independent service provider and is not affiliated with DoorKing; we install, service, and repair DoorKing access control across the valley.

Which DoorKing Models This Applies To
DoorKing’s access control line covers a wide spread: the 1800 and 1830 series telephone entry systems, the 1500 and 1520 series for multi-unit properties, the 6050 and 6100 slide gate operators with integrated access control, and the standalone 1812 keypad and proximity reader family. The series number is stamped on the inside of the housing and printed on a label near the terminal strip; the model and revision matter because DoorKing changed board layouts and reader protocols between revisions, and a reader that fits a 1830-080 won’t talk to an earlier 1830-010 without a firmware match.
For Summerlin installations, we see two failure patterns that dominate. First, the reader board itself gives out after years of desert heat cycling, and owners replace the keypad when the actual fault is the reader. Second, the controller accepts the code but the relay won’t fire, which is a board-level issue that a new keypad won’t fix. Identifying the exact revision before ordering is the difference between a one-visit repair and a second trip.
On the OEM-versus-aftermarket question, DoorKing’s own parts are the safe choice on the controller and reader boards, because the firmware and wiring harness are matched to the revision. For the housing, keypad overlay, and mounting hardware, a quality aftermarket equivalent does the same job at a lower price, and we’ll tell you which is which. You’ll get a straight recommendation, not an upsell. We also service LiftMaster, Mighty Mule, and Ghost Controls access systems if your property has a mix.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your DoorKing Access Control Is Failing
- Keypad accepts the code but the gate doesn’t move. The keypad is fine; the relay on the controller board has failed or the wiring between the reader and the operator has a break. This is the most common DoorKing fault we see on Summerlin properties.
- The entry panel shows a busy signal or won’t dial out. On 1800-series telephone entry, the phone line or cellular module has failed. Copper lines in older Summerlin neighborhoods are aging, and the module is often the culprit, not the panel.
- Codes work in the morning and fail by afternoon. Heat expansion on the terminal strip or a failing power supply. In Summerlin’s summer, surface-mounted controllers routinely see 130°F and above, and a marginal power supply fails when it’s hottest.
- The reader beeps but won’t read a card or fob. The reader’s antenna or firmware has drifted. DoorKing proximity readers are sensitive to nearby metal and to the low-voltage run, and a reader that worked for years can stop reading when the run gets wet.
- The gate opens on its own or won’t close. A stuck relay on the controller or a failed loop detector. This one is a safety issue, and it should be checked before the gate is used again.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed access control work in Summerlin runs in these ranges. Every price is quoted and agreed before any work begins, and the price you approve is the price you pay.
| Work | Installed Range |
|---|---|
| Keypad replacement (single entry) | $280 – $520 |
| Proximity or card reader replacement | $350 – $700 |
| Controller board replacement | $450 – $950 |
| Telephone entry panel (1800 series) | $1,200 – $2,400 |
| Full new access control installation | $900 – $2,400 |
The range is driven by series, revision, and whether the low-voltage wiring has to be re-run. Parts and labor are itemized on the estimate. Every completed job is backed by our written 90-Day Done Right Promise: if it isn’t right, we come back and make it right.
DIY or Call Us?
You can safely check three things without opening a panel: whether the keypad has power (look for the LED), whether the gate moves when you press the manual release, and whether the code works on a second keypad if you have one. That narrows the fault without touching live low-voltage wiring. What you shouldn’t do is open the controller housing or probe the board with a meter. Access control panels carry low-voltage control wiring alongside 120V line power, and a slip against the wrong terminal is a shock hazard, not a lesson. DoorKing boards are also revision-specific, and a wrong swap can take out the operator. If the code isn’t the problem, call us at (866) 623-9848. Estimates are free, and we’ll tell you plainly whether it’s a part or a wiring fault.
FAQs
A properly installed DoorKing keypad or reader typically gives 7 to 12 years in Summerlin’s climate, with the reader and power supply usually failing before the controller. Surface-mounted units in direct afternoon sun run shorter, so we recommend shading the housing where the property allows it. Call (866) 623-9848 for an exact quote on your system – estimates are free.
Often, yes. Relay failures, firmware drift, and wiring breaks are usually repairable at a fraction of replacement cost, and we’ll tell you when repair is the better call rather than pushing a new install. Board failures on very old revisions are the exception. Call (866) 623-9848 and we’ll give you a straight answer.
A keypad or reader replacement is typically a single visit of one to two hours, and most Summerlin jobs are completed same-day with no return trip. Full telephone entry panel replacement takes longer and is scheduled. Call (866) 623-9848 for a time window – the price is agreed before we start.
We match the exact series and revision before ordering, sourcing OEM DoorKing parts for boards and readers and a quality aftermarket equivalent for housings and hardware where it saves you money without cutting reliability. We don’t carry parts on a truck; the correct part is ordered to your model. Call (866) 623-9848 for a free estimate and a second opinion on any written quote you’ve received.
Written by the team at Ironworks Gate Co. Summerlin, serving Summerlin and nearby areas.