Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateDoorKing Gate Installation in Summerlin: What to Know First
We install and replace DoorKing gate operators and complete gate systems in Summerlin, and most straightforward installations are measured, ordered, and scheduled within a week or two rather than done same-day. We quote the full price in writing and agree it with you before any work starts, so the number you approve is the number on the bill. This page is for Summerlin homeowners who already own a DoorKing operator, or who are replacing an older gate and want a DoorKing system set up correctly from the start. Call (866) 623-9848 for a free estimate.

How DoorKing Products Fail – and How We Fix Them
DoorKing builds heavy-duty commercial-grade equipment that also lands on a lot of Summerlin residential driveways: the 6002 and 6050 slide gate operators, the 6400 swing series, and the 1833 and 1835 access controllers are the ones we see most. Because the hardware is built for harder duty than most homes give it, the failures we find usually trace back to installation choices and desert conditions rather than weak parts.
- Slide operator pads that settle or crack. On the 6002 and 6050, a concrete pad that wasn’t poured thick enough or wasn’t set on properly compacted ground will shift as the soil moves. The chain then runs at an angle, and the operator eats sprockets and chain in a matter of months. We cut out and repour the pad at the correct depth and set the operator back to level.
- Chain tension drift from Summerlin heat. Steel expands and contracts through Summerlin’s 100-degree summers and cool winter nights. A chain that’s tensioned tight in January will be slack by July, and a slack chain jumps the sprocket and stalls the operator. We set tension with the season in mind and show you the sag point to watch.
- Loop and photo-eye failures from blowing dust. The 1833 controller will simply stop accepting a command when an induction loop has been nicked by a shovel or a photo-eye lens is packed with dust and grit. On a lot of these calls the operator is fine and the accessories are the problem. We test each loop and eye individually before recommending any hardware.
- Swing operator hinges and arms wearing out. The 6400 series arms take a beating on gates that sag. If the gate leaf has dropped even a half inch, the arm fights the hinge every cycle and the motor works harder than it should. We true the hinges and gate frame first, so the operator isn’t asked to fix a gate problem.
- Boards and batteries killed by surge and neglect. A control board that’s been through a lightning-season power surge, or a backup battery that’s four years old, will cause erratic opening or a gate that quits mid-travel. We test the battery under load and check the board before we quote a replacement.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our DoorKing Gate Installation Process
A DoorKing job here runs in a set order, and we don’t skip steps to save a trip.
- 1
Free on-site measure and site check. We look at the driveway grade, the gate weight and travel, the power run, and where the loops and safety edges will go, then give you a written price.
- 2
Parts decision. DoorKing OEM parts fit correctly and keep the equipment within spec. Quality aftermarket is a fair option on some wear items and we’ll tell you honestly where it makes sense and where it doesn’t.
- 3
Pad and mounting. We set the operator on a solid, level base with the correct anchors and clearance, so the gate operates within its designed limits.
- 4
Power and safety devices. We handle the power run and set the safety edges, photo-eyes, and loops so the gate reverses and stops the way it should.
- 5
Full cycle test and walkthrough. We run the gate through its full travel, check the limits and force settings, and show you how it should sound and behave.
- 6
Written guarantee. Every completed job is backed by our 90-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
AfterWhat DoorKing Gate Installation Costs in Summerlin
These are the ranges Summerlin homeowners typically see for DoorKing work. Your exact price depends on the gate, the site, and the operator model.
| Job | Typical range |
|---|---|
| DoorKing slide operator installation (6002/6050 class) | $1,800 – $3,500 |
| DoorKing swing operator installation (6400 series) | $1,500 – $3,000 |
| New pad, mounting, and chain setup | $400 – $900 |
| Access control wiring and safety devices | $300 – $800 |
| Full gate-and-operator package | $3,500 – $7,500 |
Gate weight, driveway grade, distance from power, and whether we’re fitting to an existing gate or building new all move the number. We quote upfront and agree it with you before a bolt is turned. At your free measure, mention $50 Off Any Repair Over $250, the Free Second Opinion on Any Written Estimate, and our permanent 5% Senior and Veteran discount. Call (866) 623-9848 for an exact quote.
Why Summerlin Homeowners Call Ironworks Gate Co. Summerlin for DoorKing Work
We’re an independent DoorKing service provider, not affiliated with or authorized by DoorKing, and that independence is why our advice is yours. Our technicians have up to 13 years of experience and are background-checked and uniformed, working in your home the way they’d work in their own mother’s. We’re trained and equipped on nine gate-automation brands, including LiftMaster, Mighty Mule, and Ghost Controls, so if a DoorKing board is backordered or the right call is a different system, we can say so plainly. A live person answers the phone 24 hours a day, seven days a week. Every job is backed by our written 90-Day Done Right Promise.
FAQs
Is my DoorKing installation covered by a warranty? Yes. Every installation we complete is protected by our 90-Day Done Right Promise, which covers our workmanship in writing with no paperwork to argue over. If it’s not right, we come back and make it right.
Can you get DoorKing parts for my Summerlin gate? In most cases, yes. We source DoorKing components and quality aftermarket parts, and we’ll walk you through the OEM-versus-aftermarket difference so you’re choosing with open eyes. Call (866) 623-9848 to check availability for your model.
Should I repair my DoorKing operator or replace it? It depends on the model, its age, and the condition of the control board and motor. If the operator is sound and the failure is in the pad, chain, or accessories, repair is usually the smarter spend. If the board and motor are both failing, replacement is often the better value. We give a free second opinion on any written estimate.
How fast can you install a new DoorKing system? Most installations are scheduled within a week or two of the measure. Same-day work is for repairs, not new installs, and we’ll give you a real date up front. Call (866) 623-9848 to get on the schedule.
Do you handle the power run and the safety edges? Yes. A correct DoorKing installation includes the power run and all safety devices, including photo-eyes, safety edges, and loops. We test each one before we sign off.
Ready for a DoorKing gate that works the way it should? Call Ironworks Gate Co. Summerlin at (866) 623-9848 for a free estimate. We’ll measure on site, give you a written price, and stand behind the work in writing.
Written by the team at Ironworks Gate Co. Summerlin, serving Summerlin and nearby areas.