Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateDoorKing Gate Motor Replacement: The Summerlin Owner’s Guide
We install DoorKing gate motor replacements for Summerlin homeowners, and most driveways here land in the $1,150 to $2,600 installed range depending on the model and operator type. Because DoorKing units are common on the estate gates throughout The Ridges and Red Rock Country Club, we often have the right fix ready for a call the same day it comes in. Owners usually discover the failure the same way: the gate stops reversing, the motor hums without moving the arm, or the operator trips a breaker in the middle of the afternoon.

Which DoorKing Models This Applies To
DoorKing builds both slide gate operators (the 9000, 9100, 9200, and 9300 series, along with the newer 9500) and swing operators (the 6400 and 6500 series), and the replacement motor assembly differs by series in ways that matter. The 9000 family uses a right-angle gear reduction with a specific motor mount plate, while the 9200 and 9300 add an encoder wheel that has to match the control board revision or the gate will learn its limits incorrectly. Finding your model is the first step: the data plate is on the inside of the operator housing, usually a silver sticker with the series and serial number. A common gotcha is that a 9200 built before 2016 uses a different motor pulley diameter than later runs, so a replacement matched by series name alone can fit but run at the wrong speed.
On the OEM-versus-aftermarket question, we install genuine DoorKing motor assemblies when the operator is under ten years old and the control board is healthy, because a matched OEM part keeps the warranty and the original travel limits intact. For older operators where the motor is one of several tired components, a quality aftermarket replacement is a reasonable choice, and we tell Summerlin owners honestly when that saves money without cutting the lifespan. We’re an independent service provider, not affiliated with DoorKing, and we also service LiftMaster, Mighty Mule, and Ghost Controls operators across Summerlin.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your DoorKing Gate Motor Replacement Is Failing
- The gate hums but won’t move. This usually points to a failed start capacitor or a seized motor bearing, and on a DoorKing swing operator it often shows up first on hot afternoons. If the gate reverses after a pause, the motor is stalling under load.
- The gate moves slowly or unevenly. Worn motor brushes or a failing gearbox will drag the travel speed down, and the operator may not fully open or close before its timer expires. This is the most common early motor failure we see in Summerlin.
- Repeated breaker trips or blown fuses. A motor drawing too much current as it wears will trip the circuit, and this points to motor windings rather than the control board. It’s a fire-adjacent symptom worth taking seriously.
- Loud grinding or clicking from the housing. This signals internal gear or bearing wear, and it gets worse fast once it starts. Left alone, it can damage the control board and turn a motor job into a full operator replacement.
- The control board reports a motor fault. Many DoorKing boards display a fault code or blink pattern when they detect a motor issue. That code tells us whether the motor, the encoder, or the board itself is the culprit.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Summerlin, a DoorKing gate motor replacement runs $1,150 to $2,600 installed, and the price is settled upfront before a single bolt is turned. Slide operators sit at the lower end; swing operators and units with encoder or control board complications sit at the higher end. The range depends on the series, whether the gearbox or board is also worn, and how accessible the operator housing is. Your quote covers the motor assembly, the labor, the travel-limit reset, and a full gate test. Every job is backed by our written 90-Day Done Right Promise, so if it isn’t right, we come back and make it right. Right now we’re running $50 off any repair over $250, a free second opinion on any written estimate, and a permanent 5% senior and veteran discount.

DIY or Call Us?
You can safely check a few things yourself: confirm the operator has power, look for a tripped breaker, inspect the data plate for the model number, and clear debris from the gate track. Past that, the work involves line voltage and a high-torque motor, and getting the travel limits or encoder wrong can damage the control board or leave a gate that won’t reverse on contact. We don’t recommend homeowners swap the motor themselves. Our technicians have up to 13 years of experience and are trained on DoorKing alongside the other major brands, so the right part gets matched on the first visit. Call (866) 623-9848 and we’ll take it from there.
FAQs
A DoorKing motor typically lasts 10 to 15 years with regular use, though Summerlin’s heat and dust shorten that, and operators on sunny west-facing driveways often fail closer to the 10-year mark.
Sometimes. A failed start capacitor or worn brushes can be replaced on their own, but once the windings or gearbox are gone, a full motor replacement is the honest fix.
Most DoorKing motor replacements take two to four hours, including the travel-limit reset and a full open-and-close test, and many Summerlin jobs are finished in a single visit.
We match the motor assembly to your exact DoorKing series and control board revision, then order genuine DoorKing or quality aftermarket parts based on your operator’s age and condition, never guessing from the series name alone.
Written by the team at Ironworks Gate Co. Summerlin, serving Summerlin and nearby areas.