Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateDoorKing Hinge & Roller Replacement: The Summerlin Owner’s Guide
We replace failing DoorKing hinges and rollers with the correct replacement part for your gate model, and most Summerlin jobs are done on a single visit. Installed cost typically runs $145 to $360 per gate, parts and labor together, and the price is settled with you before we turn a bolt. DoorKing swing-gate hardware is a different beast from what hangs on a typical driveway gate, so the part has to match your operator line, not just the gate.

Owners usually find the problem before they call. The gate starts dragging through the last foot of travel. One hinge squeals through every cycle and the squeal gets louder over a few weeks. Or the leaf has sagged just enough that the opener strains, reverses, and refuses to latch. In Summerlin, where gates sit on sun-exposed masonry walls through 100-degree afternoons, that wear shows up faster than most homeowners expect.
Which DoorKing Models This Applies To
DoorKing hardware lives on both swing operators and slide operators, and the hinge and roller spec depends on which one you have. On swing gates, the 6000 and 6400 series operators drive heavy steel leaves that hang on adjustable hinges with a specific pin diameter and mounting pattern; the leaf weight and frame thickness decide the hardware. On slide gates, the 9000 and 9300 series operators use a trolley and roller arrangement on a V-groove or flat track, and the roller diameter and groove profile have to match the track’s. Two gates that look identical at the curb often carry different hardware.
The reliable way to identify your part is to read the operator label on the housing, then measure the hinge pin or roller diameter with calipers before you order anything. Matching by eye is how the wrong part ends up in the driveway.
On the OEM-versus-aftermarket question, DoorKing’s own hardware is a known quantity. Quality aftermarket equivalents do exist, and on many swing-gate hinge applications they hold up well. Our view is simple: match the load, match the finish, and don’t put a light-duty replacement on a heavy estate leaf just to save a few dollars. We’re an independent service provider and not affiliated with DoorKing; we work on their hardware every week and know where the substitutes are safe and where they aren’t. We also service LiftMaster, Mighty Mule, and Ghost Controls, so the part you need is one we can source correctly.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your DoorKing Hinge & Roller Replacement Is Failing
Five symptoms show up again and again on Summerlin gates, and each one points at something specific.
- The gate sags at the latch end. A worn hinge pin or a flattened roller washer lets the leaf drop a fraction of an inch, which is enough to foul the striker.
- The leaf drags or rubs through part of its travel. A roller that has worn flat or come out of its groove stops carrying the weight, so the gate rides on the frame.
- A rhythmic squeal or grind on every cycle. That’s metal on metal inside a hinge or a dry roller bearing; the noise is the warning, not the problem.
- The operator strains, reverses, or times out. When a hinge binds, the opener fights extra resistance and often trips its safety reverse before the gate closes.
- Visible play or rust bleed at the hinge. Grab the gate and rock it; more than a slight flex means the hinge has worn beyond adjustment. Our desert sun hardens and cracks older lubricant, and rust bleed at the pin tells you the bearing surface is gone.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
On a Summerlin gate, a standard hinge and roller swap runs about $145 to $260 for a light to mid-weight leaf and $260 to $360 for a heavy estate gate with multiple hinges per leaf. That range covers the parts, the labor, alignment after the swap, and a full cycle test.
What pushes a job toward the top of the range: heavy leaves that need the gate lifted and rehung, a seized or corroded pin, hinges with a hard-to-match mounting pattern, or a slide track that also needs attention. We price the parts and the labor separately on the estimate so you can see exactly what you’re paying for, and the number you agree to is the number on the bill. Every job is covered by our written 90-Day Done Right Promise; if it isn’t right, we come back and make it right.
DIY or Call Us?
You can safely check a few things yourself. Rock the leaf by hand and note where the play is. Look at the hinge pins for rust or a worn groove. Wipe a roller clean and see whether it turns freely. Write down the operator model from the housing label. That information speeds up the call and lets us bring the right part.
Where DIY goes wrong: a heavy estate leaf can weigh several hundred pounds, and a hinge pin that lets go while the gate is off its latch can drop it on a hand or a foot. Pair that with an operator still energized and you have a real hazard. DoorKing hardware is not the place to learn by doing. If you’d rather not lift a gate that size on a Saturday, call us at (866) 623-9848 and we’ll get it sorted.
FAQs
Expect five to ten years on a residential gate, less on a heavy estate leaf or a gate in full afternoon sun through Summerlin summers, where the heat cooks the lubricant and accelerates pin wear. If your hardware is past that window and the gate has started dragging, plan on replacement rather than another adjustment.
Sometimes. A loose hinge can often be re-adjusted, and a dry bearing can be cleaned and relubricated. But once a pin is worn thin or a roller is flat, adjustment buys a few months at best and then the gate fails again. We’ll tell you which one you’re looking at before you spend the money.
A single swing gate with standard hinges and rollers is typically a same-day job, usually an hour or two on site. Heavy estate gates or a slide gate with a trolley and track take longer, and we’ll book the time accordingly.
We match your operator model and measured specs to the correct DoorKing-compatible hinge or roller, then confirm fit on the gate before we finish. We don’t guess at the size. If you have the operator label and a pin diameter, we can have the right part ready when we arrive.
Written by the team at Ironworks Gate Co. Summerlin, serving Summerlin and nearby areas.
If a dragging gate or a squealing hinge has been nagging at you, call Ironworks Gate Co. Summerlin at (866) 623-9848 for a free estimate. Upfront pricing, a written 90-Day Done Right Promise, and a live person answers the phone any hour of the day.