Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateDoorKing Welding & Fabrication: The Summerlin Owner’s Guide
We repair and re-fabricate DoorKing gate hardware for Summerlin homeowners, and most welding and fabrication jobs run $275 to $850 installed depending on whether we’re re-welding an existing hinge or building a replacement mount from scratch. Welding work is scheduled rather than dispatched, so you’ll get a free on-site measure and a written price before we touch the gate. Owners usually find the problem the hard way: a gate that sags a half-inch one week and drags the ground the next, a hinge that’s torn its welds out of the post, or a mounting plate that’s cracked around the bolts after years of desert heat cycling. DoorKing operators are tough, but the steel around them takes the beating.

Which DoorKing Models This Applies To
DoorKing makes slide and swing gate operators across several lines – the 9000 series sliding operators, the 6000 and 6400 swing operators, and the 1500 series for lighter residential use – and the fabrication needs differ sharply between them. Slide operators ride on a bottom track and carriage assembly, and that’s where we see the most weld fatigue. Swing operators rely on hinge welds and mounting plates taking the full torque of the arm every cycle. To identify your unit, look for the metal data plate inside the operator housing; it carries the model and serial. Measure your gate’s actual leaf width and weight before ordering anything, because DoorKing’s arm and bracket sizing is tied to those numbers, not to the model number alone.
On the OEM-versus-aftermarket question, DoorKing’s factory brackets and carriage parts are the reference standard, and for load-bearing weldments we lean OEM or a fabricator-built equivalent matched to the original spec. Generic aftermarket hinge plates often run thinner gauge steel, which matters more in Summerlin than most places. A note on affiliation: Ironworks Gate Co. Summerlin is an independent service provider and is not affiliated with DoorKing. We also service LiftMaster, Mighty Mule, and Ghost Controls equipment on the same driveways.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your DoorKing Welding & Fabrication Is Failing
- The gate sags or drags within a few inches of travel. That’s usually a hinge weld that’s cracked and letting the leaf shift, not an operator fault – the motor is working harder to overcome a geometry problem.
- Visible cracks or rust streaks at the weld bead. Summerlin’s dry heat and intense sun age paint and expose bare steel at weld joints, and once moisture gets into a hairline crack the corrosion spreads under the coating.
- Grinding, popping, or a shudder as the gate moves. A loose carriage bolt or a fatigued mounting plate lets the assembly shift under load, and the noise is metal moving where it shouldn’t.
- The operator trips its overload or reverses mid-travel. Rising resistance from a misaligned or dragging gate triggers the safety circuit – the operator is protecting itself from a fabrication problem.
- Bolts that won’t stay tight no longer holding torque. Enlarged or elongated bolt holes in a cracked plate mean the steel, not the fastener, has failed.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Summerlin, expect roughly $275 to $450 for re-welding and re-aligning an existing hinge or bracket, and $475 to $850 for a fabricated replacement mount, carriage repair, or post reinforcement built to match your DoorKing operator. The range comes down to access, whether the gate has to come off its hinges, how much old weld has to be ground out, and whether the steel needs refinishing afterward. We quote parts and labor together as one upfront price and settle it before a single bolt is turned. Our welding work is backed by our written 90-Day Done Right Promise: if it isn’t right, we come back and make it right. Ask about $50 off any repair over $250 and the standing 5% senior and veteran discount.
DIY or Call Us?
You can safely check a few things yourself: look for cracks at the weld beads, test whether bolts hold torque, and confirm the gate swings or slides freely by hand with the operator disengaged. What we’d steer you away from is welding on a loaded gate or an energized operator. Gate steel is under tension, and arc welding near an operator’s control board or battery backup can damage electronics or, worse, shock you. Structural weld repair on a gate that weighs hundreds of pounds isn’t a first-project job. If your DoorKing gate is sagging, cracking, or grinding, call us at (866) 623-9848 for a free estimate. A live person answers around the clock.
FAQs
A properly executed weld on quality steel typically holds 10 to 15 years in our climate, but Summerlin’s 100-plus-degree summers and intense UV shorten paint life and let corrosion into joints faster than in cooler regions, so annual inspection pays off. Call (866) 623-9848 for a free second opinion on any written estimate.
Often yes – a cracked hinge weld or a fatigued bracket can frequently be re-welded and reinforced rather than replaced outright, which is why we measure before recommending a swap. We’ll tell you honestly which path serves the gate. Call (866) 623-9848 and we’ll take a look.
Most single-location fabrication jobs are completed in one visit of a few hours once the part is sourced, though custom-fabricated mounts may need a short lead time for the steel. We confirm scheduling and price with you upfront. Call (866) 623-9848 to book a free measure.
We match your DoorKing model and gate dimensions to the correct bracket, carriage, or hinge spec, sourcing OEM or a fabricator-built equivalent to the original gauge and load rating rather than a thin aftermarket substitute. That’s the difference between a fix that lasts and one that fails next summer.
Written by the team at Ironworks Gate Co. Summerlin, serving Summerlin and nearby areas.