Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateElite Welding & Fabrication: The Summerlin Owner’s Guide
We repair and re-fabricate the welded steel components on Elite gate systems throughout Summerlin – hinges, hinge posts, frame corners, mounting plates, and drive-arm brackets – and a welded load-bearing repair typically runs $280 to $650 installed, with most repairs done in a single visit. Fabrication and re-welding work of that kind is scheduled rather than dispatched same-day, because we check the gate structure before we quote it, but the visit itself is one trip. Owners usually find us the same way: the gate starts to sag at the latch end, the outer frame corners show rust bloom, or the swing hangs at a slight angle and the Elite operator begins straining or hitting its force limit. In Summerlin, that first sag often shows up after a dry summer followed by the first hard winter wind.

Which Elite Models This Applies To
Elite’s residential swing gate operators share much of their mounting architecture across series, but the weld points and bracket geometry that matter for fabrication work are specific to how your gate was built, not just the operator model. The most reliable starting point is the data label inside the operator housing – it lists the model and serial, and that tells us the drive-arm dimensions and the torque the frame has to carry. From there we measure the gate leaf: overall width, leaf height, frame tube thickness (typically 1.5″ to 2″ square tube on residential swings), hinge spacing, and post size. That combination is what we fabricate to. A common compatibility gotcha in Summerlin: two gates on the same street built by the same fabricator in the same era can carry different hinge hardware, so a bracket that fits your neighbor’s Elite-equipped gate may not locate correctly on yours. On the OEM-versus-aftermarket decision, we source Elite-compatible components where the original part is the correct fit, and a quality aftermarket hinge or bracket where the original design is the weak point – for example, a cast hinge that has already cracked once. We are an independent service provider and not affiliated with Elite; we simply know the platform.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Elite Welding & Fabrication Is Failing
- Sag at the latch end of the gate. The hinge-side weld or hinge post has begun to give, and the gate settles under its own weight. Left alone, the operator’s drive arm starts fighting the sag.
- Rust bloom at frame corners and weld seams. Summerlin’s dry heat does not stop rust – it hides it, because the ground stays dry while sprinkler overspray and morning condensation sit in the seams. Once a seam is compromised, the frame tube holds water.
- Visible cracks or pitting at a hinge weld. A hairline crack in a load-bearing weld is a structural problem, not cosmetic. It grows each time the operator swings the gate.
- The gate racks or twists as it opens. A cracked mounting plate or a weld failure at the operator bracket lets the leaf flex out of square. The Elite operator compensates with more force until it faults.
- The operator strains or trips its force limit. When the gate drags or binds because the steel has moved, the operator is doing work the frame should absorb. We see this pattern especially on gates past the fifteen-year mark.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Pricing on Elite gate fabrication depends on the weld scope, not the operator. In the Summerlin market, expect $280 to $650 installed for a load-bearing welded repair, and $650 to $1,400 where a hinge post is reset in the ground or a section of frame is cut out and replaced. The range is driven by how much steel has to come out, whether the post is set in concrete, and whether the gate has to be taken off its hinges to weld it flat. That price is quoted and agreed before any work starts – you’ll see the parts and labor spelled out, not bundled into one number. Every fabrication job carries our 90-Day Done Right Promise: if a weld we made is not right, we come back and make it right. We also offer $50 off any repair over $250.
DIY or Call Us?
You can safely check a few things yourself: look for rust stains running down from a seam, feel for wobble at the hinge when the gate is closed, and note whether the gate sits level at the latch. What you should not do yourself is weld or re-weld a load-bearing hinge, mounting bracket, or drive-arm connection. A gate leaf can weigh several hundred pounds; a weld that looks sound but has poor penetration can let the gate drop, and the danger is not just the gate – it is you under it. Structural welding on a gate that carries an Elite operator also has to account for the operator’s force and travel, which is not something to guess at. If your gate is sagging or you’ve seen a crack, call us at (866) 623-9848 and we’ll give you an honest read before any repair.
FAQs
Fifteen to twenty years is typical for a properly welded steel gate frame in Summerlin’s climate, provided the welds were sound to begin with and the seams stay protected. Sprinkler overspray is the most common reason we see them fail earlier.
Often yes. Many hinge and corner failures are repaired by grinding out the failed weld and re-welding with proper penetration, rather than cutting the frame apart. We’ll tell you honestly which is the right call after we look at it.
Most welded repairs are completed in a single visit, typically a few hours on site, because we measure and fabricate to fit rather than welding freehand. Jobs that require resetting a post in concrete may take longer, and that is scheduled ahead of time.
We identify your operator from the data label and measure your existing gate hardware, then source the correct Elite-compatible component or fabricate the weld to fit. Because we service the correct fix rather than a one-size part, the fit is right the first time, and the price is quoted before we start.
Written by the team at Ironworks Gate Co. Summerlin, serving Summerlin and nearby areas.