Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFAAC Gate Motor Replacement: The Summerlin Owner’s Guide
We replace failed and failing FAAC gate motors in Summerlin, and most single-swing residential jobs run $850 to $1,600 installed for the motor and operator, depending on model and gate weight. If your gate is stuck open right now, call us and a live person answers, day or night. Most replacement jobs are completed in a single visit with the price settled before we start.

Owners in Summerlin usually find this the same way. The gate opens halfway and reverses. Or it makes a grinding sound for a week, then quits. Or the arm swings loose because the hinge pin inside the operator has worn oval. By the time a FAAC motor reaches us, it’s usually been complaining for a month. The 390, 391, 400, and 422 series are the ones we see most on Summerlin estate gates, and the failure modes follow the heat. Call (866) 623-9848 for a free estimate and we’ll tell you whether it’s the motor, the control board, or the battery backup.
Key Takeaways
- Typical Summerlin installed price: $850 to $1,600 for a single-swing FAAC replacement.
- Most jobs are done in a single visit, price quoted and agreed before we turn a wrench.
- We service nine brands, but on this page we’re talking FAAC specifically.
- Every job is backed by our written 90-Day Done Right Promise.
Which FAAC Models This Applies To
FAAC builds two families of residential swing operators, and the replacement part depends entirely on which one you have. The 390/391 series uses a hydraulic operator with a separate locking hydraulic unit; the 400/422 series is electromechanical with a worm gear inside the arm. They are not interchangeable. A 390 arm will not bolt to a 422 mount, and the control board wiring is different. If you’re not sure, look for the data plate on the underside of the operator housing or inside the control box door. It reads like “390 24V” or “422 CBAC.” Photograph it before you call. That photo saves a trip.
Summerlin gates are often heavy – wrought iron in The Ridges and Red Rock Country Club, decorative aluminum in Sun City Summerlin. Weight matters. The 422 handles a leaf up to about 13 feet and 880 pounds; the 390 handles less. Overspecifying is fine. Underspecifying a heavy gate is what kills a motor early. We’ll measure your leaf and tell you which model actually fits.
On the OEM-vs-aftermarket question: FAAC’s own replacement motors are the safest match, but for discontinued series a quality aftermarket equivalent exists and works when specified correctly. We won’t put a cheap import arm on a $40,000 gate. We’ll tell you which one we’d put on our own.
One more thing. Ironworks Gate Co. Summerlin is an independent service provider. We are not affiliated with FAAC.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your FAAC Gate Motor Replacement Is Failing
These are the symptoms that tell us the motor itself is done, not just the control board or a limit switch. Each one has a cause, and the cause tells us what to replace.
- The gate reverses mid-travel. The operator is sensing resistance and treating it as an obstruction. On older FAAC units this is usually a worn worm gear binding inside the arm, or a hydraulic seal weeping.
- Grinding or growling from the housing. Gear teeth wearing flat. Once you hear it, the gear is already past saving – replacing the motor is cheaper than rebuilding the gearbox.
- The gate drifts open or won’t hold closed. On 390-series units the hydraulic lock is losing pressure. On 422 units it’s usually a failed limit switch or the brake.
- Motor hums but nothing moves. The capacitor has failed, or the motor winding is shorted. A failed capacitor is a $30 part; a burned winding means a new motor.
- Repeated control-board faults after a power blink. In Summerlin, monsoon-season surges and NV Energy switching bumps fry control boards on older FAAC operators. A board is sometimes fixable; often it’s a sign the whole operator is at end of life.
Any of these can also be caused by a bad battery backup, a worn hinge, or a misaligned gate leaf. That’s why we check the whole gate before quoting a motor. We don’t want to sell you a motor you don’t need.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing in Summerlin runs $850 to $1,600 for a single-swing residential FAAC replacement. Here’s the honest breakdown of what moves that number:
- Motor and operator: $500 to $950 depending on model (390 vs 422) and OEM vs quality aftermarket.
- Labor: $250 to $450 for a standard swap of the same model on the same mount. Different mount or different model runs more.
- Low-voltage wiring and control board: $0 to $200 if existing wiring is re-used and the control box is sound.
- Battery backup: $120 to $220 if your unit uses one.
- Old motor haul-away and disposal: included.
We quote the full price in writing before we start. No surprises on the bill. Every job is backed by our written 90-Day Done Right Promise, no paperwork needed, no arguing – if it’s not right, we come back and make it right. Right now, $50 off any repair over $250, free second opinion on any written estimate, and 5% off for seniors and veterans.
DIY or Call Us?
What you can safely check: whether the gate leaf swings freely by hand with the motor disengaged (most FAAC arms have a manual release key), whether the control box has power, and whether the battery backup is charged. Those three checks tell you a lot and cost nothing.
Where DIY goes wrong on a FAAC: the swing operator mounts to a welded post or a concrete pad, and the geometry has to be exact. If the arm angle is off by a few degrees, the motor binds and burns out in months. There’s also 24-volt DC and often 120-volt AC at the control box – real electrical hazard, and NV requires it done safely. And a gate you install wrong can crush a car, a pet, or a person. This is not a job for a weekend and a YouTube video. Most Summerlin homeowners don’t need to hear that twice.
Call (866) 623-9848 for a free estimate. We’ll tell you what’s actually wrong and quote the exact price before we touch a bolt.
FAQs
Seven to twelve years for a well-installed residential FAAC unit in Summerlin, and less than that on gates over 500 pounds or in full afternoon sun. Our summers are hard on hydraulic seals and capacitors. If your unit is past eight years, plan for a replacement rather than a third repair.
Often, yes – a bad capacitor, control board, or limit switch is a repair, not a replacement, and we’ll tell you when that’s the honest call. A worn worm gear or a failed motor winding is usually replacement territory. Call (866) 623-9848 for a free second opinion on any written estimate; we’d rather repair your motor than sell you a new one.
Most single-swing same-model FAAC replacements are done in one visit of two to four hours, and the gate is running the same day. Different-mount replacements, dual-leaf gates, or jobs needing new low-voltage wiring take longer, and we schedule those.
We match the exact model number from your data plate and order from suppliers we use for FAAC equipment specifically – OEM where available, quality aftermarket when the OEM series is discontinued. We do not install generic arms on estate gates. We’ll tell you which one we’d put on our own gate and stand behind the choice.
Call (866) 623-9848 for a free estimate. We also service LiftMaster, Mighty Mule, and Ghost Controls, plus BFT, Linear, Viking, DoorKing, and Elite. Weekends and evenings, a live person answers. Senior and veteran discount always available. We’re Ironworks Gate Co. Summerlin, and we stand behind the work.
Written by the team at Ironworks Gate Co. Summerlin, serving Summerlin and nearby areas.