A Ironworks company - serving Summerlin, NV

FAAC Hinge & Roller Replacement in Summerlin, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

FAAC Hinge & Roller Replacement: The Summerlin Owner’s Guide

We replace failed FAAC hinges and rollers with FAAC-compatible parts, and for most Summerlin driveways the installed cost lands between $185 and $340 for a hinge set and $120 to $260 for a roller and track carrier swap. Because the parts are small and the labor is straightforward, this is a same-day repair when you call before mid-afternoon. Most owners find out the hard way: the gate starts dragging on the backswing, the leaf hangs a quarter-inch low at the latch, or a roller shrieks through the whole travel and the opener begins to strain. A hinge that shears rarely announces itself. It fails quietly, and by then the actuator has been fighting the friction for weeks.

professional gate motor & opener service in Summerlin, NV

Call (866) 623-9848

Which FAAC Models This Applies To

FAAC builds swing and sliding operators on more than one platform, and the hinge and roller hardware is not interchangeable across them. The 400 and 390 series swing operators use a different hinge plate pattern than the 740/750 sliding line, and the S418 and C720 sliding operators take roller carriers sized to the beam profile, not the gate weight alone. In Summerlin we see the 400 series most often on residential swing gates and the 740 on wider sliding leaves. The way to identify your part: read the model plate on the operator housing itself (not the control box), then measure the existing hinge hole centers and the roller wheel diameter. Those two measurements catch most ordering mistakes. On the OEM-versus-aftermarket decision, FAAC-branded parts fit consistently and cost more. Quality aftermarket equivalents made to the same spec are a reasonable middle path when the original is discontinued. What we avoid is the generic hardware-store hinge, which is a different alloy and a different bearing load rating. Ironworks Gate Co. Summerlin is an independent service provider and is not affiliated with FAAC.

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Signs Your FAAC Hinge & Roller Replacement Is Failing

Most failures show up as one of these five patterns. Catching them early protects the operator, which is the expensive part.

  • The gate sags at the latch side. A worn hinge pin or a wallowed hinge plate lets the leaf drop. The symptom is usually a latch that no longer catches without a lift.
  • A grinding or squealing sound through travel. That is a roller bearing that has run dry or seized. Nevada’s dust gets into the bearing and the grease dries out in the summer heat, so a roller that sounded fine in March can be crying by July.
  • The opener strains or trips its overload. When the gate drags on a bad roller, the motor works harder and the controller sees it as a fault. Owners often blame the motor when the roller is the cause.
  • Visible play at the hinge. Grab the gate and rock it. More than a little movement means the pin or the plate is worn. On a heavy leaf, a loose hinge puts load on welds that were never meant to carry it.
  • Roller wheels worn flat or cracked. A flat spot makes the gate lurch and bounce, and a cracked wheel can shed a chunk and bind the track. Check the wheel faces for scuffing and any crack.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Here in Summerlin, a FAAC hinge set runs about $185 to $340 installed, and a roller and carrier replacement runs about $120 to $260, assuming the hardware is available for your model. We give a clear, itemized price before we touch the gate, so you know the parts cost and the labor cost and there are no surprises on the bill. What drives the range: the number of hinges or rollers, whether the track needs adjustment, and whether the worn hinge has already damaged a weld or a mounting plate. Every job includes a check of the operator’s travel and a test cycle. The work is covered by our written 90-Day Done Right Promise, and if something is not right we come back and make it right.

DIY or Call Us?

Some of this you can check safely. Look at the hinge pins for play, listen for a grinding roller, and clean the track of grit and debris. What we’d rather you not attempt is the replacement itself on a heavy swing leaf. A gate that comes off its hinge under load or drops when a pin is pulled can cause a serious injury, and the door and gate hardware on a residential drive is not the place to test a method. The other trap: the wrong part, or the right part installed with the fold over-torqued or the hinge pin not seated, and the failure repeats within weeks. If you are unsure whether it is the hinge, the roller, or the operator, call us and we will tell you honestly. Call (866) 623-9848 – a live person answers, 24 hours a day.

professional gate motor & opener service in Summerlin, NV

FAQs

How long does a FAAC hinge or roller last? A properly maintained FAAC hinge and roller on a residential gate typically lasts several years, but in Summerlin’s heat and dusty conditions, rollers can seize in as little as two seasons if not cleaned and re-greased. Hinges tend to last longer than rollers on the same gate. A call before the next dry spell is worth it.

Can it be repaired instead of replaced? Sometimes. A hinge pin can be re-pinned and a roller bearing re-greased if the wear has not gone too far. Once the pin has wallowed the plate or the wheel has gone out of round, replacement is the honest answer. We will tell you which one your gate needs.

How long does the swap take? A single hinge or roller swap is usually a short visit, often under an hour once we’re on site. A full hinge and roller replacement on a wider sliding gate takes longer because the leaf has to be supported and aligned. We’ll give you a realistic window when you call.

How do you source the part? We match the part to your FAAC model plate and measurements, then source from suppliers we trust for that platform. We carry no stock of parts on a truck; the right part is ordered for your gate. Call (866) 623-9848 for a free estimate and we will confirm what your model needs.

Whether it’s a single squeaking roller or a set of tired hinges on a heavy swing leaf, this is a repair that protects the operator and the gate. If it is dragging, grinding, or sagging, call us and we’ll get a live person on the line and a clear price before any work starts. Call (866) 623-9848 – estimates are free, and our 90-Day Done Right Promise stands behind the work. We also service LiftMaster, Mighty Mule, and Ghost Controls systems across Summerlin.

Written by the team at Ironworks Gate Co. Summerlin.

Need Gate Repair help nationwide? Licensed & insured · 60-minute response · free estimates
Call (866) 623-9848
Local Service Coverage

Request a Free Estimate in Summerlin

Tell us what you need - Ironworks Gate Co. Summerlin responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Call Now - 24/7 Dispatch