Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Gate Motor Replacement: The Summerlin Owner’s Guide
We install Ghost Controls-compatible gate motor replacement in Summerlin, and a full motor swap typically runs $650 to $1,100 installed depending on the arm you choose and the condition of the gate. Because a dead motor usually means a gate stuck open or stuck shut, we treat these as priority calls and can often get to Summerlin the same day. Most owners discover the problem the same way: the arm runs but the gate won’t move, the operator clicks and stops, or the gate reverses halfway through travel. When you call, a live person answers any hour, and we’ll give you an honest read before anyone is dispatched.

Which Ghost Controls Models This Applies To
Ghost Controls builds single and dual swing-gate operators for residential driveways, and the replacement arm has to match the series and the gate’s geometry, not just the brand. The label under the control box or on the rear of the arm tells you the model number. If the label has faded, we measure the gate leaf width, the post spacing, and the arm’s extended and retracted length to identify the correct replacement. The gotchas we see most in Summerlin: a single-arm operator being asked to swing a leaf that’s too wide or too heavy, and a mismatched arm that fits the mount but not the stroke, so the gate never reaches full open.
On the OEM-versus-aftermarket question, Ghost Controls’ own replacement arms are the safe match for series compatibility, and a quality aftermarket arm can work when the specs line up exactly. We’re straight about the tradeoff: a correct aftermarket arm saves money, but a wrong spec costs you a second visit. We’re an independent service provider and not affiliated with Ghost Controls, so our advice is about what fits your gate and lasts in Summerlin’s heat.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Ghost Controls Gate Motor Replacement Is Failing
- The arm runs but the gate doesn’t move. Usually a stripped gear or a failed drive coupling inside the housing, which means the motor is turning with nothing to push against.
- Clicks and stops, or trips the breaker. A failing control board or a motor drawing too much current. In Summerlin’s summer heat, an older operator’s windings weaken faster and the arm stalls under load.
- The gate reverses partway through travel. Often a failing limit switch or an obstruction sensor that reads a phantom hit. We check the safety edges and the board before condemning the motor.
- Grinding or a loud whine on open or close. Worn gears or a dry, neglected gearbox. A seized arm loads the whole operator and shortens its life.
- Inconsistent or dead manual release. The release key or lever sticking means you can’t get the gate open by hand when the power’s out, which is a real safety issue in Summerlin.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed Ghost Controls-compatible motor replacement in Summerlin generally lands between $650 and $1,100. The range moves with the arm series (single vs. dual), whether the control board and safety edges survive the swap, and the condition of the gate itself. A sturdy, well-hung gate takes a straightforward motor swap; a gate that sags or binds adds fabrication or hinge work. Parts and labor are broken out in the quote, and the price is agreed before a single bolt is turned. Every job carries our written 90-Day Done Right Promise, and the current $50 Off Any Repair Over $250 applies.
| Item | Typical Range (Installed) |
|---|---|
| Single-arm operator replacement | $650 – $850 |
| Dual-arm operator replacement | $900 – $1,100 |
| Control board add-on | Quoted separately |
| Gate repair/binding correction | Quoted separately |
DIY or Call Us?
A homeowner can safely check a few things: the power at the outlet, the model label, whether the manual release works, and whether the gate swings freely by hand with the operator disengaged. What we don’t recommend is opening the operator housing or swapping the arm yourself. The arm is under load, and a powered gate that moves unexpectedly can injure fingers, hands, or worse, especially around the pinch points between arm and gate. A gate operator is a machine that has to be re-tuned after any swap, from the limits to the safety edges. That’s the part DIY gets wrong, and it’s the part we do on the first visit. Call (866) 623-9848 and we’ll walk you through what’s safe to check.
FAQs
Most residential Ghost Controls arms last roughly eight to twelve years, but Summerlin’s heat and dust can shorten that. UV on the housing and dry gears are the usual culprits.
Sometimes, yes. A failed control board, limit switch, or safety edge can often be repaired without a full motor swap. We diagnose first and quote repair against replacement so you can decide.
A single-arm replacement is usually a few hours, and a dual-arm swap takes most of a day once the correct part is on hand. We confirm the timing when we quote.
We order the correct Ghost Controls-compatible arm matched to your model and gate, then install and tune it. Bring us the label or the dimensions and we’ll handle the rest.
Ready to get your gate working again? Call (866) 623-9848 for a free estimate. We’ll confirm the right Ghost Controls-compatible part for your Summerlin gate, quote it upfront, and stand behind the work in writing.
Written by the team at Ironworks Gate Co. Summerlin, serving Summerlin and nearby areas.