A Ironworks company - serving Summerlin, NV

Ghost Controls Welding & Fabrication in Summerlin, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Ghost Controls Welding & Fabrication: The Summerlin Owner’s Guide

We repair and replace failed Ghost Controls welds and fabrication points on driveway gates throughout Summerlin, and most welded repairs land between $240 and $680 installed depending on whether we are reinforcing a hinge post, rebuilding a gate frame corner, or re-hanging a sagging leaf. When a weld goes, you usually find out at the worst moment: the gate drops a half inch and drags the driveway, the arm bracket pulls loose from the frame and the opener strains, or you hear a pop when the wind catches the gate and the frame flexes where it used to be solid. Ghost Controls operators are reliable, but they push a gate leaf hard, and a weld that was never quite right from the beginning will eventually show it. In Summerlin, where afternoon heat and dry air work on outdoor steel year after year, those welds show it sooner than most owners expect.

Professional welder using an angle grinder for metal gate repair services in Summerlin, NV

Call (866) 623-9848

Which Ghost Controls Models This Applies To

Ghost Controls builds a single line of residential solar and low-voltage swing openers – the TSS1, TS1, and the heavier ARM and TDS series arms – and all of them bolt to the gate frame through brackets and plates that depend on sound welds. The opener is not usually the problem. The gate is. Where it matters is the connection points: the operator arm bracket welded to the gate leaf, the hinge post, the frame corners, and the cross-bracing on a double gate. Those are the welds that carry the load, and they are the ones we see fail.

To identify your setup before you call, look at the control box or the arm housing for the model stamp, and measure the gate leaf width and the distance from hinge to the operator bracket. Those two numbers tell us more than any photo. On the parts decision: Ghost Controls sells replacement brackets and mounting hardware, but it does not sell you a stronger weld. An OEM bracket bolted to a cracked frame will crack again. The right fix is matching the bracket to the gate with fabrication that holds – which is where an independent shop like ours comes in. We are not affiliated with Ghost Controls; we service their equipment and the gates it moves. We also work on LiftMaster, Mighty Mule, and DoorKing systems when a Summerlin gate has one of those instead.

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Signs Your Ghost Controls Welding & Fabrication Is Failing

Weld failures rarely announce themselves with a snap. They creep. Here is what Summerlin owners describe when they call us:

  • The gate sags and drags on the driveway. A failed weld at the hinge post or frame corner lets the leaf drop under its own weight, and the drag gets worse each week.
  • The operator arm bracket is loose or cracked at the frame. The opener pushes and pulls at that bracket thousands of times a year; a hairline crack opens and the arm starts to wobble.
  • You hear a pop or clunk when the gate starts or stops. Metal moving where it should be rigid. That sound is the frame flexing at a weld that has given up.
  • Rust streaks or powder-coat cracking along a joint. In Summerlin’s dry climate, rust at a weld seam means moisture got in through a fracture, not surface wear.
  • The gate binds or twists as it swings. A twisted leaf puts the opener under load it was never designed for, and the motor runs hot or the arm strains.

Any one of these is worth a look. Two or more together mean the gate is working against the operator, and the longer it runs that way the more you spend.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Welded repair and fabrication on a Ghost Controls gate in Summerlin runs $240 to $680 installed, quoted and agreed before a single bolt is turned. Here is what moves the number:

Professional welder using an angle grinder for metal gate repair services in Summerlin, NV
  • Repair type: a simple bracket re-weld sits at the low end; rebuilding a frame corner or reinforcing a hinge post pushes toward the top.
  • Gate material and finish: steel, aluminum, and ornamental iron each weld differently, and a powder-coated gate needs the finish touched up to hold.
  • Access and gate size: a wide double gate or a tight side-yard job takes longer than a single pedestrian gate.
  • Re-alignment: once the weld is sound, the gate and arm usually need to be re-hung and the opener re-set so it travels true again.

The price you agree to is the price on the bill. Every job is backed by our written 90-Day Done Right Promise: if it is not right, we come back and make it right, no arguing.

DIY or Call Us?

There is real danger here, and we will say so plainly. Gate frames carry several hundred pounds, and a sagging leaf can drop or swing without warning while you are working under it. Welding on a gate that is still attached to a powered operator means working near stored energy, and a home welder on a loaded frame is how people get hurt. That said, an owner can safely check a few things: look for rust streaks and cracks at the joints, wiggle the operator bracket by hand with the opener off, and listen for the pop. What goes wrong with DIY fabrication is the diagnosis – bolting a brace onto the wrong part of the frame or welding over a crack without relieving the load just delays the failure and can damage the operator. When the weld is the question, call (866) 623-9848 and we will tell you straight.

FAQs

How long does a Ghost Controls gate weld last in Summerlin? A properly executed weld with the finish protected should last years, not months. Summerlin’s dry heat is easier on steel than coastal salt air, but the real lifespan depends on whether the weld was loaded correctly and the powder coat was restored – a good weld with exposed bare metal will rust at the seam within a season or two.

Can you repair the weld instead of replacing the whole gate? Yes, in most cases. A failed bracket or frame corner can be cut out and re-welded, re-hung, and re-aligned to the opener without replacing the gate. We only recommend a new gate when the frame is rusted through or repeatedly cracked in several places.

How long does the repair take? Most welded repairs are completed in a single visit, typically two to four hours including re-alignment of the gate and resetting the Ghost Controls arm. We confirm the schedule when we quote.

How do you source the part? We match the bracket or hardware to your specific Ghost Controls model and fabricate or supply the correct part for the gate, then weld it in place and test the full travel with the opener. Nothing is ordered blind; we measure first.

Call (866) 623-9848 for a free estimate.

Written by the team at Ironworks Gate Co. Summerlin, serving Summerlin and nearby areas.

Need Gate Repair help nationwide? Licensed & insured · 60-minute response · free estimates
Call (866) 623-9848
Local Service Coverage

Request a Free Estimate in Summerlin

Tell us what you need - Ironworks Gate Co. Summerlin responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Call Now - 24/7 Dispatch