Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateLinear Welding & Fabrication: The Summerlin Owner’s Guide
Welding and fabrication work on a Linear gate system in Summerlin usually runs $280 to $850 for a bracket, hinge, post or arm repair, and most of that work is done on a single visit. A full custom fabrication – a new frame, a re-welded post, a rebuilt operator mount – is quoted after we measure on site. If your gate is sagging, dragging, or you can hear the motor straining against metal that no longer lines up, the fabrication side of your Linear system has likely failed, not the electronics.

Summerlin owners usually discover this the same way. The gate stops closing flush. The bottom corner scrapes the driveway after a few hot weeks. The operator arm pulls the gate at an odd angle and the hinges start to squeal. By the time the phone rings, the weld at the hinge plate has often been cracked for months. We see it in The Ridges, in Red Rock Country Club, and on the older iron gates along the western edges of Summerlin where afternoon sun hits the same panel for six hours a day.
Which Linear Models This Applies To
Linear swing and slide operators – the LSO, LSG, and the older SW series swing gate openers – all mount to gate hardware we fabricate and repair. The operator itself rarely fails first. What fails first is the metal it’s bolted to. If your Linear label on the control box says LSO50 or LSO24, the arm geometry matters: the mounting plate and hinge post have to hold their exact position, or the operator will bind and eventually burn out. A plate that’s moved a quarter inch is enough.
To confirm which generation you have, look at the sticker inside the operator housing. Note the model and the serial prefix. Then measure three things: the hinge post diameter, the gate frame thickness, and the distance from the hinge to the operator’s mounting bracket. Bring those numbers to any conversation with us and the quote gets sharper.
On OEM versus aftermarket: Linear-branded hinge plates and arm brackets are available, but for most of the welding and fabrication work on a Summerlin gate, the right answer is neither. It’s fabricated steel made to fit what’s actually in your driveway. Original Linear parts fit original Linear gates. After 15 or 20 years, gates have moved, twisted, and been re-hung. We fabricate to the gate in front of us, not to a catalog drawing from 2008.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Linear Welding & Fabrication Is Failing
- The gate sags at the latch side. The hinge weld or the hinge post plate has cracked underneath the paint. You’ll see a hairline crack in the powder coat or a rust streak running down from the hinge.
- The operator arm pulls at an angle, then the motor overheats. The mounting bracket has shifted or the frame has bent. The operator is doing what it’s told; the metal isn’t holding its position.
- The gate scrapes the driveway on hot afternoons. Summerlin ground shifts with soil moisture and the frame has twisted. A twisted frame will chew through hinges and eventually break the operator gearbox.
- Hinges squeal or the gate wobbles when pushed by hand. The hinge pin bore has worn oval. Welding a new bore is the repair; swapping a hinge pin won’t hold.
- Visible rust bleeding through the bottom rail or post base. The steel has been thinning for years. Once it’s thin enough, no weld will hold – that section gets cut out and replaced.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Summerlin, welding and fabrication work on a Linear-gated system falls into these ranges. Every price is quoted and agreed before we strike an arc.
| Work | Typical installed range |
|---|---|
| Hinge weld repair or re-weld one hinge plate | $280 – $420 |
| Operator mounting bracket fabricated and installed | $340 – $550 |
| Hinge post reinforcement or post plate replacement | $450 – $850 |
| Gate frame straightening and re-weld (multi-point) | $600 – $1,200 |
| Custom frame section or bottom rail fabrication | Quoted on site |
What drives the range: how much of the gate needs cutting out, whether the gate has to come off its hinges to weld properly, and how much paint or powder coat has to come off and go back on. Labor, materials, and a fresh finish on the repaired area are in the price. Every job is covered by our written 90-Day Done Right Promise, and we also offer $50 Off Any Repair Over $250.
DIY or Call Us?
You can safely do a few things yourself. Push the gate by hand from open to closed and watch for the point where it binds. Check every hinge for a rust streak. Look at the operator arm’s mounting plate for cracks in the paint. Write down the Linear model from the housing sticker. None of these involve touching the metal or the motor.
Where owners get into trouble is welding on the gate while it’s still attached to the operator and powered. Welding current will find its way through the gate frame into the control board and destroy it. We see it every few months in Summerlin: a homeowner or handyman welds a bracket, the gate works for a week, then the Linear board fails. We disconnect, isolate, and weld properly, and we can service the operator too, since we’re trained on Linear along with LiftMaster, Mighty Mule, and Ghost Controls. Call (866) 623-9848 and we’ll tell you honestly whether the gate needs welding or the operator needs attention first.
FAQs
A properly fabricated and welded hinge or bracket should last 15 to 25 years on a residential gate. The limiting factor in Summerlin isn’t the weld – it’s the sun. The western exposure on most Summerlin properties causes the powder coat to chalk and fail within 8 to 12 years, and once the coating goes, the steel underneath starts to pit. We prime and coat every repaired area to reset that clock.
Yes, most of the time. A cracked hinge weld or a shifted operator bracket is a repair, not a replacement. The gate frame stays. Only when the steel itself has thinned below what will hold a weld does a section get cut out and replaced. We’ll show you the failed area before we do anything, and the price is settled upfront.
Most hinge and bracket repairs are done in a single visit, typically two to three hours. Multi-point frame straightening takes a full day. Custom fabrication on a bottom rail or post section is scheduled separately once we’ve measured on site, and we’ll give you a written date, not a window.
Linear hardware comes through Linear’s distribution network. Fabricated parts – brackets, plates, frame sections – we make ourselves from steel matched to your gate’s thickness and load. We’re an independent service provider and not affiliated with Linear, and we don’t carry parts on a truck. That means the part is right for your gate, not the closest thing that happened to be in stock.
If your Linear-gated Summerlin property needs a weld, a bracket, or a full fabrication, call Ironworks Gate Co. Summerlin at (866) 623-9848 for a free estimate. We’ll be there when we say, quote the price upfront, and back the work in writing with the 90-Day Done Right Promise.
Written by the team at Ironworks Gate Co. Summerlin, serving Summerlin and nearby areas.