Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateMighty Mule Access Control Installation: The Summerlin Owner’s Guide
We install Mighty Mule access control systems in Summerlin, and most completed jobs land between $450 and $1,400 installed, depending on whether you’re replacing a keypad and receiver only or adding a full entry setup with an intercom and vehicle exit loop. Many of these are done in a single visit once the correct part is matched to your opener. Owners usually find out something has failed the same way every time: the gate opens fine from the remote but the keypad won’t take the code, or the clicker works from the driveway and not from the house. That gap between “the gate works” and “the entry point doesn’t” is the access control talking, not the motor.

Before we go further, one plain statement: Ironworks Gate Co. Summerlin is an independent service provider. We are not affiliated with Mighty Mule, and we don’t speak for them. What we do is service their equipment, alongside LiftMaster, Ghost Controls, DoorKing, and six other lines, so the correct fix gets made on the first visit.
Key Takeaways
- Access control failure rarely means the gate motor is bad. It means the keypad, receiver, or wiring between them has failed.
- Installed pricing in Summerlin runs roughly $450 to $1,400.
- The price is quoted and agreed before any work starts. No surprises on the bill.
- Our technicians have up to 13 years of experience, and every job is backed by our written 90-Day Done Right Promise.
Which Mighty Mule Models This Applies To
Mighty Mule’s access control hardware shows up across their swing and slide opener lines, and the compatibility gotcha that trips up most Summerlin owners is this: the wireless keypad and the receiver inside the control box are two separate parts that look like one system. You can buy a new keypad that matches your opener and still get nothing, because the receiver board is the piece that actually failed. Before spending a dollar, we read the model label on the opener’s control box (MM260, MM360, MM560, and the slide series all appear in Summerlin driveways) and confirm which receiver generation it takes. Older receiver boards and newer keypads don’t always talk to each other, and no amount of reprogramming fixes a mismatch.
On OEM versus aftermarket for Mighty Mule specifically: Mighty Mule’s own transmitters and receivers are the safe choice when you want plug-and-play. Quality aftermarket equivalents exist and cost less, but they vary in signal range and in how well they hold a code in heat. In Summerlin’s summer afternoons, a control box bolted to a west-facing gate post can sit well past 130 degrees inside. We’ve seen cheap aftermarket receivers lose their programming in that heat within a season. That’s not a sales pitch; it’s a reality of the desert that shows up in callbacks. We’ll tell you honestly which route fits your gate, and we never claim to keep parts in stock or on a truck. The part gets sourced for your job.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Mighty Mule Access Control Installation Is Failing
These are the symptoms Summerlin owners describe to us, and what’s usually behind each one.
- Keypad takes the code but the gate doesn’t move. The keypad is working; the receiver or the wire run between them has failed. Loose connections at the control box terminals are the usual culprit.
- Remote works close up, not from the house. Signal range has dropped, often from a failing receiver or a corroded antenna connection. Sun and dust on the antenna are common in Summerlin.
- The gate opens on its own. A stuck keypad button, a receiver picking up a neighbor’s signal, or a code that’s being held. This is worth a same-day look, not a wait-and-see.
- Codes won’t save after reprogramming. The receiver’s memory is failing. Reprogramming buys days, not months, once this starts.
- Intermittent operation that gets worse in the afternoon heat. A control board or receiver on its way out. Heat speeds up the failure; it doesn’t cause it.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Honest pricing for Summerlin, installed:
| Scope | Typical Installed Range |
|---|---|
| Keypad or receiver replacement, reprogram | $450 – $700 |
| Keypad plus receiver plus wiring repair | $700 – $1,000 |
| Full entry setup with intercom and exit loop | $1,000 – $1,400 |
What drives the number: whether the wire run needs repair, whether the control box is mounted in full sun (we may recommend relocating it), and whether your existing Mighty Mule opener is compatible with current receiver hardware. The price covers the part and the labor together, quoted upfront and agreed before we start. Every completed job carries our written 90-Day Done Right Promise: if it’s not right, we come back and make it right. Active offers that apply here include $50 Off Any Repair Over $250, a Free Second Opinion on Any Written Estimate, and a permanent 5% Senior and Veteran discount.

DIY or Call Us?
There are safe things to check yourself, and there are things that go wrong in ways you won’t see. Safe: confirm the keypad has fresh batteries, look for visible corrosion on the antenna, and check that the control box door is closed and sealed. Those three checks solve a surprising share of calls.
Where DIY goes sideways: swapping a receiver board or re-running wires inside the control box means working around line voltage and the opener’s low-voltage terminals in the same enclosure. Getting that wrong can damage a control board that was fine, or leave a gate that moves when it shouldn’t. We’d rather you not risk it, and we’d rather not sell you a part you didn’t need. If the gate’s behavior changed and you can’t trace it to a battery, call us for a free estimate.
FAQs
Expect 5 to 8 years from a keypad and receiver in Summerlin’s heat, shorter if the control box sits in direct afternoon sun. The receivers fail before the keypads, almost every time. Relocating a sun-baked control box or adding a simple shade cover is the single best way to stretch that lifespan.
Sometimes, yes. A loose terminal, a corroded antenna, or a dead keypad battery is a genuine repair, not a replacement. A receiver that won’t hold a code is not worth repairing; its memory is failing and reprogramming won’t fix it. We’ll tell you which one you’re looking at before anyone turns a bolt.
A keypad and receiver swap is usually a single visit of about an hour to ninety minutes, once the correct part is on hand. If the wiring needs repair, plan on a longer visit. We schedule the work so the part is there before we arrive, so you aren’t waiting on a second trip.
We order the specific receiver and keypad generation that matches your Mighty Mule opener, from suppliers we trust to ship the right model. We don’t claim to carry stock or keep parts on a truck; the part is sourced for your job. That’s how the right part gets here the first time, and why the fix holds through the summer.
If your Mighty Mule gate talks to the remote but ignores the keypad, that’s an access control problem we handle every week in Summerlin. Call (866) 623-9848 for a free estimate. A live person answers, 24 hours a day, seven days a week. We’ll quote the price upfront, agree it with you before any work starts, and back the job in writing. Done right, and backed in writing.
Written by the team at Ironworks Gate Co. Summerlin, serving Summerlin and nearby areas.