Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateMighty Mule Gate Motor & Opener in Summerlin: What to Know First
We repair, replace, and install Mighty Mule gate motors and openers across Summerlin, and most swing-gate control-board and battery faults are diagnosed and corrected on the first visit. A straightforward board or battery replacement typically runs $260 to $480; a full motor replacement with new arms or a fresh operator runs $700 to $1,400 depending on the gate. We’re an independent Mighty Mule service provider, not affiliated with or authorized by the manufacturer, and we quote the price and get your agreement before any work starts.

This page is for the homeowner with a Mighty Mule operator already on the driveway, or one who’s decided on Mighty Mule and wants it installed correctly. If that’s you, call (866) 623-9848. A live person answers, day or night.
How Mighty Mule Products Fail – and How We Fix Them
Mighty Mule is a do-it-yourself-friendly brand, and that’s how a lot of Summerlin installations start: a homeowner or a prior handyman mounts the operator, wires it, and it runs fine for years. The failures we see on Mighty Mule jobs tend to be different from what goes wrong on a LiftMaster or FAAC. Here are the patterns our technicians run into most.
- Control board corrosion on the MM560 and similar residential swing operators. Dust, irrigation overspray, and monsoon-season humidity work into the control box, and the board’s push-button terminals and limit inputs corrode before the motor ever fails. The symptom is a gate that stutters, runs partway, then stops, or an operator that clicks but doesn’t move. We clean and reseal, and when the board is gone we replace it with a factory board so the next owner isn’t chasing someone’s solder work.
- Battery failure on solar and battery-backup units. The MM260, MM360, and their single-panel solar kits run off a 12-volt battery, and in a Summerlin summer those batteries cook. A battery that’s two summers old will hold enough charge to open once and then sag, so the gate opens and won’t close, or the second open of the day dies halfway. We load-test the battery and the solar panel output together, because a weak panel will eat a new battery too.
- Gear and arm wear on the older MM500 and MM600 lines. These operators are tough, but the acme screw and the drive gear wear against a gate that has sagged or a hinge that’s stiff. Owners often replace the motor when the real problem is the gate dragging. We check the gate swing, the hinges, and the post before we touch the operator, and we tell you honestly which one is failing.
- Limit-switch drift after a gate settles. Summerlin homes sit on expansive clay soils, and a gate post can shift a fraction of an inch over a winter. That’s enough to throw off the open and close limits on a Mighty Mule arm operator, so the gate slams, reverses, or stops short. It’s a small adjustment, but done wrong it strips the arm or burns the board.
- Undersized wiring and voltage drop on long driveway runs. A lot of Mighty Mule openers get wired with too-light gauge wire from a garage or a yard box a hundred feet away, and the operator browns out on startup. That shows up as an intermittent fault that only happens on hot afternoons when the gate gets stiff. We check the voltage at the operator under load, not just at rest, and we’ll tell you if the wire has to be upsized before the operator can be trusted.
On the safety side, gate operators store real force and spring-loaded arms can release hard. We don’t recommend adjusting arms, limits, or spring tension yourself; that’s the part to hand to a trained technician.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Mighty Mule Gate Motor & Opener Process
Here’s how a Mighty Mule job runs from the first call to the last bolt.
- 1
We take the call and ask the right questions. A live person answers and gets the model if you have it, what the gate is doing, and whether it’s one leaf or two. We book you in.
- 2
We diagnose on site. The technician tests the gate swing, the hinges, the battery or solar input, the control board, the limits, and the supply voltage under load. We check the gate first and the operator second, so we’re fixing the cause.
- 3
We make the parts decision and tell you why. Where a factory Mighty Mule part is the right call for reliability and warranty, we use it. Where a quality aftermarket arm or battery is the better value for an older operator, we say so and quote both.
- 4
We give you the price before we start. The number is settled and you agree to it before a bolt is turned. No surprises on the bill.
- 5
We do the repair or installation and test it hard. We run the gate through full open and close cycles, check the safety reverse, and confirm the battery backup holds under load, not just at rest.
- 6
We clean up and back it in writing. Every job is covered by our 90-Day Done Right Promise. If it isn’t right, we come back and make it right.
What Mighty Mule Gate Motor & Opener Costs in Summerlin
Every gate is different, so treat these as ranges, not a quote. The number we give you on site is the number you pay.
- Diagnostic visit and adjustment: $95 to $150, credited toward the repair.
- Battery or solar panel replacement: $180 to $340.
- Control board replacement: $260 to $480.
- Arm, gear, or acme screw rebuild on an MM500 or MM600: $320 to $620.
- Full Mighty Mule swing-operator replacement (single leaf): $700 to $1,100.
- Dual-leaf swing operator with new arms and safety edges: $1,300 to $2,200.
- Slide operator replacement: $900 to $1,800 depending on the gate weight and track condition.
What moves the price: gate weight and condition, whether the wire gauge is up to the run, whether you want battery backup or solar, and whether the gate needs welding or hinge work before the operator can be trusted. Installation and replacement are measured and scheduled work, not same-day; we give you a free measure and a written price. Call (866) 623-9848. Estimates are free.
See the difference
Before
After
Before
After
Before
AfterWhy Summerlin Homeowners Call Ironworks Gate Co. Summerlin for Mighty Mule Work
We’ve been doing gate work in this community for over 42 years, and we plan to be here another forty. That’s the whole reason we stand behind every job with the 90-Day Done Right Promise: a written guarantee, no paperwork, no arguing. If we did the work and it isn’t right, we come back and fix it.
A live person answers our phone 24 hours a day, 7 days a week. Our technicians are background-checked, uniformed, and bring up to 13 years of experience to the driveway, working in your home the way they’d work in their own mother’s. We’re trained on nine gate-automation brands, so if the job turns out to call for a LiftMaster, Ghost Controls, or DoorKing part, we’re not guessing. Most jobs finish in a single visit, with the price settled upfront. For Summerlin homeowners who want a Mighty Mule operator done once and done right, we’re the call. Ask about our $50 off any repair over $250 and our free second opinion on any written estimate.
FAQs
We’re an independent Mighty Mule service provider, so we can’t perform manufacturer warranty work, but we do warranty-safe repairs using factory parts where the factory part is the right call, and we’ll tell you when a repair would be the smart move before the manufacturer’s warranty window closes. On our own work, our 90-Day Done Right Promise covers it. Call (866) 623-9848 for an exact quote.
Usually yes, and for the common models the parts we need on a first visit are the usual suspects: control boards, batteries, solar panels, and arm or gear components. On a very old operator, aftermarket arms and batteries are often the better value, and we’ll quote factory and aftermarket side by side so you can decide. Call (866) 623-9848 for an exact quote.
If the operator is under about ten years old and the motor and gear are sound, a board, battery, or arm repair is almost always the right call and costs a fraction of a new unit. If the motor is failing, the housing is corroded, or the gate has changed weight, replacement is the honest answer. We test the gate and the operator before we recommend anything. Call (866) 623-9848 for an exact quote.
On most Mighty Mule swing operators that’s a safety-reverse fault, a limit-switch issue, or a failing battery that can’t hold charge through a full cycle. It’s worth having the limits and the safety circuit tested before you replace the operator. Call (866) 623-9848 for an exact quote.
Most Mighty Mule repairs are scheduled within a short window, and we’ll tell you the soonest slot when you call. New operator installation is measured and scheduled, not same-day. Call (866) 623-9848 for an exact quote, and estimates are free.
Get Your Mighty Mule Gate Fixed
If your Mighty Mule operator is stuttering, dying on the second open, or just plain worn out, call Ironworks Gate Co. Summerlin at (866) 623-9848 for a free estimate. A live person answers, the price is settled before we start, and every job is backed in writing. We serve Summerlin and nearby areas.
Written by the team at Ironworks Gate Co. Summerlin, serving Summerlin and nearby areas.