Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Parts & Welding for Summerlin Homeowners
When a gate hinge shears or a post pulls loose, the whole entry stops working the way it should, and the gate starts to sag or drag on the driveway. Our technicians have up to 13 years of experience with gate parts and welding in Summerlin, from discreet courtyard gates in The Ridges to wide double-drive units up in Reverence, and a live person answers the phone here 24 hours a day. We repair, replace, and weld on site so most jobs are finished in a single visit. Call (866) 623-9848 and we’ll get a trained technician out to look at it.

What Our Gate Parts & Welding Service Includes
Gate parts and welding cover the hard structure of the gate: the metal that holds the weight. When those parts wear, the gate sags, drags, won’t latch, or won’t swing true. Here is what we handle in Summerlin.
Hinge Replacement
Hinges carry the full weight of the gate leaf, and when they wear out the gate drops and drags against the ground or the post. In Summerlin’s dry heat, a hinge that has gone years without grease often seizes before it fails, and we see it on steel gates that face west into the afternoon sun. We cut out the worn hinge, weld a new one on square, and adjust the alignment so the gate swings free again.

Post Replacement
A gate post that leans is usually underground, not up top: water gets into the footing or the steel rusts through at the grade line. Once the post is off plumb, no amount of hinge adjustment will keep the gate closing right. We remove the old post, set a new one properly, and reset the gate so everything lines up again from the frame down.

Rail Repair
Rails are the horizontal bars that give the gate its stiffness, and a bent or cracked rail lets the whole leaf flex and twist. Impact damage from a car, a bike, or a hit from a delivery truck bends rails more often than you’d think. We straighten what can be straightened, cut out and re-weld what can’t, and match the finish so the repair doesn’t stand out.

Custom Welding
Sometimes the right part simply isn’t made, or an older gate needs a bracket, an arm mount, or a reinforcement that no catalog sells. Our technicians weld on site and in the shop for the odd shapes that fit custom architecture. This is where the metalwork shows: a clean bead, ground smooth, primed and painted, so the repair looks like it belongs on the gate instead of bolted on late.
Gate Rollers
Sliding gates ride on rollers, and once those flat-spot or seize, the gate shudders and strains the motor trying to move it. Rollers take a beating in Summerlin because grit and dust work into the track and grind them down faster than back East. We replace worn rollers, true up the track, and check the motor isn’t working harder than it should be to do a simple slide.
Latch & Lock
A latch that doesn’t catch is a gate that doesn’t secure, and it usually comes down to a worn striker, a dropped gate, or a lock that has corroded shut. We repair and replace latches and locks, from manual thumb latches to keyed and electronic units, and make sure the gate lines up so the latch grabs cleanly every time.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Brands We Service for Gate Parts & Welding
We service LiftMaster operators and know where they wear: the drive gears and the limit switches are usually the first to show age, and a gate that drags or binds will kill a LiftMaster motor faster than almost anything else. That means when we fix the metal, we also think about what that metal is doing to the opener. We work on Mighty Mule and FAAC equipment too, and we know the mounting hardware on each one well enough to know when a sagging gate is fighting the arm instead of the other way around.
Every brand wears in its own spot, and knowing those spots is how we get to the real problem on the first visit. Whether your gate runs a LiftMaster, a Mighty Mule, a FAAC, or a brand we haven’t named here, we can help. The gate and its parts come first, and the motor follows.
Signs You Need Gate Parts & Welding Right Now
- The gate sags or scrapes the ground. A gate that drags on the driveway is telling you a hinge or a post has moved, and grinding it along the concrete only makes the repair bigger. Catch it early and it’s often a hinge job; wait and it becomes a post and frame job.
- A hinge or bracket is cracked or bent. Cracks in weld joints or bent hinge plates are structural, and a gate under motor power can tear a tired bracket clean off the post. If you can see a crack, it needs welding sooner rather than later.
- The gate won’t latch or lock. A latch that misses means the gate is out of alignment, and a gate that won’t stay shut is a security gap that widens over time. This is one of the easiest things to fix when it’s caught early.
- Rust streaks or flaking paint at the joints. Rust blooming out of a weld or hinge is the metal thinning from the inside, and Summerlin’s dry climate won’t stop it once it starts. A little grinding, welding, and repaint now beats replacing the whole leaf later.
- The gate shudders or drags on its track. Flat-spotted rollers or a fouled track make a sliding gate jerk and strain, and that strain passes straight into the motor. New rollers and a trued track are usually a quick fix that saves the opener.
Our Gate Parts & Welding Process – Step by Step
- 1
We look at the whole gate, not just the broken part. A technician checks the posts, hinges, frame, rollers, and the opener together, because a hinge problem is often a symptom of a post that moved. We check plumb and level with a level and a square, and we watch the gate open and close under power so we see the drag that doesn’t show when it’s standing still.
- 2
We give you the price before we touch a bolt. You get a written upfront price for the parts and the welding, and we explain what needs fixing now and what can wait. No surprises on the bill, because the price is settled and agreed before any work starts.
- 3
We do the repair on site. Our technicians cut, weld, grind, and fit new parts right at your gate, and they cover the surrounding concrete and stucco so your driveway and entry stay clean. Every weld is ground smooth and primed and painted so it holds up.
- 4
We test the gate through a full cycle. After the metal is fixed, we open and close the gate several times under power, check the latches and rollers, and confirm the opener isn’t straining against a gate that’s still out of true. If the motor needs attention too, we’ll tell you rather than leave it to fail later.
- 5
We back it in writing. Every job is covered by our 90-Day Done Right Promise: if it isn’t right, we come back and make it right, no paperwork and no arguing. That’s the Keystone Standard, and it applies to every gate job we do in Summerlin.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Summerlin?
Gate parts and welding in Summerlin typically run $150 to $450 for a hinge, roller, or latch repair, and $400 to $1,200 or more when a post gets replaced or a rail is rebuilt. A single hinge replacement is usually the low end; a bent rail that needs cutting and re-welding sits in the middle; and a full post replacement with a new footing is the high end, especially on heavier double gates.
A few things move the price. The type of metal matters, since welding galvanized steel or aluminum takes different technique and prep than plain steel. Post replacement costs more than a hinge because it involves the footing and resetting the whole gate. Gate weight and width matter too, and so does how much the old part has corroded into the frame. Custom welding for an odd bracket or a repair no catalog part fits is quoted per job once we see it.

The way to avoid overpaying is to get the price in writing before anything is cut or welded, which is how we work anyway. Our free estimate covers the parts, the welding, and the labor, and we’ll tell you plainly if a repair isn’t worth it and a replacement is the better move. We also offer $50 off any repair over $250, a free second opinion on any written estimate, and a 5% senior and veteran discount.
| Repair | Typical Summerlin Price |
|---|---|
| Hinge replacement | $150 – $350 |
| Latch & lock repair | $150 – $300 |
| Gate rollers (set) | $180 – $400 |
| Rail repair or re-weld | $250 – $600 |
| Post replacement | $400 – $1,200+ |
| Custom welding | Quoted per job |
Call (866) 623-9848 for an exact quote on your gate. Estimates are free.
Gate Parts & Welding Near Summerlin – Our Service Area
We handle gate parts and welding for homeowners across Summerlin and the surrounding valley, including Spring Valley, Las Vegas, and Enterprise. Most Summerlin calls are scheduled within a day or two, and we give you a window we actually keep. If you’re further out toward Henderson, Boulder City, or Sandy Valley, we’ll tell you the soonest we can get there. You can see the same work we do in gate parts and welding in Spring Valley and gate parts and welding in Las Vegas.
Serving Summerlin, NV – Our Local Coverage Area
We serve Summerlin and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Gate Parts & Welding in Summerlin
Gate parts and welding is the repair and replacement of the hard metal structure of a gate: hinges, posts, rails, rollers, latches, and any custom welding needed to keep the frame strong. It’s separate from the opener or motor, which only moves the gate; the parts and welding keep it hanging straight and closing right. Most structural gate problems start here, not at the motor.
Most hinge, roller, and latch jobs are finished in a single visit of an hour or two. Post replacement and heavier welding can take longer, sometimes into a second visit if a new footing needs to set. We’ll tell you the expected time when we give the price, and we don’t leave a gate half-finished. Call (866) 623-9848 and we’ll give you a realistic window.
Most hinge, latch, and roller repairs run $150 to $400, while post replacement and rail rebuilding run $400 to $1,200 or more. The price depends on the metal, the gate weight, and how much corrosion we find once we open it up. Every price is quoted and agreed before work starts. Call (866) 623-9848 for an exact quote; estimates are free.
Yes. We service LiftMaster and Mighty Mule equipment, along with FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, and Elite. Our technicians are trained on all nine brands, so we know how each one mounts and where it wears. Whatever is on your driveway, we can fix the parts and the arm together. Call (866) 623-9848 to book a visit.
Often yes. A gate that won’t latch, won’t close, or is hanging open is a security problem, and we treat it like one. A live person answers our phone 24 hours a day, so call (866) 623-9848 and we’ll tell you the soonest we can get a technician to your gate. Many Summerlin calls are handled the same day.
Yes. Every job is covered by our written 90-Day Done Right Promise, which means if something we repaired isn’t right, we come back and make it right, no hassle and no arguing. That’s the Keystone Standard, and it applies to every gate job. It’s why homeowners call us back instead of hunting for someone new.
Clear the driveway on both sides of the gate and move anything that’s in the way of the swing or the track. If you have the opener manual or know the brand, have it handy, and tell us if the gate has been hit, dragged, or acting up under power. Leave the gate unlocked for the technician. We bring the tools, the welding gear, and the parts; you just need the space clear.
Schedule Your Gate Parts & Welding Service in Summerlin Today
A sagging gate or a cracked hinge won’t fix itself, and the longer it drags, the more it costs. Call Ironworks Gate Co. at (866) 623-9848 for a free, no-obligation estimate on gate parts and welding in Summerlin. A live person answers 24 hours a day, the price is agreed before any work starts, and every job is backed in writing by our 90-Day Done Right Promise. We’ll be there when we say.
Written by the team at Ironworks Gate Co.