Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterElectric Gate Repair in Summerlin, NV
Electric gate repair in Summerlin typically costs $195 to $650 depending on whether the fault sits in the operator, the access control, or the gate structure itself, and most jobs are finished in a single visit. If your driveway gate has stopped opening, runs a few feet and reverses, or clicks without moving, the problem is usually one of four things: a failed control board, a worn drive gear, a bad safety loop or photo-eye, or a limit switch that has drifted out of adjustment. We handle all four, plus the welding and hinge work that aging gates in Summerlin eventually need.
Ironworks Gate Co. works only on driveway and estate gates. That focus means when a LiftMaster or FAAC operator acts up, we’ve already seen the pattern before we pull into the driveway. We settle the price upfront, before a single bolt is turned, and back every job with our written 90-Day Done Right Promise. If it isn’t right, we come back and make it right. No arguing, no paperwork. To get a technician out today, call (866) 623-9848.
This page covers the electrical and mechanical side of gate service. For hinge, latch, and structural problems, see our Gate Repair in Summerlin page, and for the full scope of what we do across both, start at the main Gate Repair service page.
Key Takeaways
- Most electric gate problems in Summerlin fall into four buckets: control board, drive gear, safety sensor, or limit adjustment.
- Carriage and estate gates in Summerlin’s older custom-home neighborhoods often run on operators installed 15 or more years ago, where boards and gears are now wearing out.
- Upfront pricing is settled before work begins, and every repair carries the written 90-Day Done Right Promise.
- We’re trained and equipped on nine major gate-automation brands, so the correct parts and the correct fix happen on the first visit.
- A live person answers our phone 24 hours a day, 7 days a week. No voicemail, no callback queue.
When You Need Electric Gate Repair
Electric gate faults rarely announce themselves politely. They show up as a gate that quits mid-cycle, an opener that hums but won’t move, or a click from the control box with nothing happening after it. Here are the scenarios Summerlin homeowners describe most often.
- The gate opens partway and stops, or reverses without warning. That’s usually a limit switch that has drifted or a jammed safety loop, and it’s one of the most common calls we take in Summerlin’s gated enclaves like The Ridges and Red Rock Country Club.
- The operator hums or clicks but the gate doesn’t move. In summer heat that regularly climbs past 105 degrees, drive gears and control boards in older Mighty Mule and LiftMaster units are prone to thermal damage. A hum with no motion usually points to a stripped gear or a failed capacitor.
- The gate won’t respond to the remote or keypad. Could be a dead receiver, a mismatched remote frequency, or a control board that needs replacing. Sometimes it’s just a keypad gone bad after years of summer sun.
- Loud grinding, popping, or dragging as the gate moves. Worn hinge pins, a bent track, or a slipping chain. Left alone, a grinding gate chews through gears and turns a modest repair into a motor replacement.
- The gate stops mid-travel when a car pulls up. Failing safety photo-eyes are the usual cause, and they should be repaired promptly rather than bypassed. A gate that doesn’t recognize an obstacle is a liability.
- The control box trips the breaker or shows no power. Wiring, a shorted board, or a failing transformer. This is electrical work and not something to poke at yourself.
Our Electric Gate Repair Process
We follow the same disciplined sequence on every job, whether it’s a quick sensor swap or a full operator rebuild. The 400th job gets the same care as the first.
- Confirm the symptoms and the operator. We ask what the gate is doing and what brand it’s running. That heads-up lets us bring the right board, gear, or sensor for your LiftMaster, FAAC, BFT, or whichever of the nine brands is on your driveway.
- Inspect the whole system, not just the fault. A technician checks the operator, control board, safety loops, photo-eyes, limit switches, hinges, and gate frame. We find the root cause so the repair holds.
- Give you an upfront price and the options. You get a clear diagnosis and a written price before any work starts. If there’s a repair-or-replace call to make, we lay out both so you decide.
- Complete the repair on the spot when possible. Most jobs are done in a single visit. Our technicians have up to 13 years of experience and carry the parts to finish the common fixes without a return trip.
- Test the gate through full cycles and confirm safety reversal. We run the gate open and closed, check that it reverses on obstruction, and walk you through what was done. Then the 90-Day Done Right Promise stands behind it in writing.
Electric Gate Repair Pricing in Summerlin
Electric gate repair in Summerlin runs from about $195 for a sensor or limit adjustment to $650 or more for a drive gear rebuild or control board replacement. A full operator replacement, if it comes to that, is a larger number and depends on the brand and gate weight. We settle the price with you before touching the gate, so there are no surprises on the bill.
| Repair | Typical Range |
|---|---|
| Safety sensor / photo-eye replacement | $195 – $320 |
| Limit switch adjustment or replacement | $175 – $280 |
| Remote receiver or keypad service | $150 – $350 |
| Control board replacement | $350 – $650 |
| Drive gear / operator rebuild | $400 – $650 |
| Full operator replacement | Quoted per gate and brand |
What pushes a job toward the higher end: the age of the operator, whether the brand’s parts are in stock, gate weight and travel length on long estate gates, and whether wiring needs rerouting. Summerlin’s dry heat and intense sun age outdoor control boxes and keypads faster than cooler climates, so UV-fatigued components surface often.
Two standing offers help here: $50 Off Any Repair Over $250, and a Free Second Opinion on Any Written Estimate if another company has already quoted you. We also run an $89 Seasonal Tune-Up and a permanent 5% Senior and Veteran discount. Estimates are free, so call (866) 623-9848 for an exact quote.
FAQs – Electric Gate Repair
How much does electric gate repair cost in Summerlin?
Electric gate repair in Summerlin typically costs $195 to $650, with most common repairs (sensors, limits, keypads) landing between $150 and $350. The final number depends on the operator brand, the part involved, and gate size. Call (866) 623-9848 for a free estimate; we settle the price upfront before any work begins.
Can you repair my electric gate the same day?
Yes, most electric gate repairs are completed in a single visit, often the same day you call. Because we’re equipped on nine gate-automation brands including LiftMaster, FAAC, and BFT, we usually bring the correct part the first time. Call (866) 623-9848 and a live person will answer, 24 hours a day.
My gate won’t open to the remote. Is that a serious problem?
Not usually. A gate that ignores the remote, keypad, or both is often a dead receiver battery, a failed receiver, or a control board issue, and most of these are straightforward repairs. It’s worth checking that the operator still has power first. Then call us for a diagnosis. We offer free estimates, so there’s no cost to find out.
Is it cheaper to repair the operator or replace it?
Repair is usually the better value unless the operator is badly aged or the control board and drive gear have both failed. As a rule, if a repair costs more than half the price of a comparable new operator, replacement makes more sense. We’ll show you both numbers and let you decide. Backed by our written 90-Day Done Right Promise on the work we do either way.
Can I fix my electric gate myself?
No, we don’t recommend it. Gate operators run on line voltage and drive heavy arms under real force, and a gate that reverses at the wrong moment can seriously injure someone. Control boards, wiring, and safety sensors are work for a trained technician. We’re licensed and insured for this, and we’ll get it right the first time.
When your electric gate stops cooperating, the fix is a phone call away. Ironworks Gate Co. has been the dedicated gate specialist Summerlin homeowners rely on because we do the job right and back it in writing. We’ll be there when we say, settle a square price upfront, and stand behind the work. Call (866) 623-9848 today for a free estimate. You can also explore our gate motor repair, gate opener repair, and gate access control services, or check nearby coverage with gate repair in Henderson and gate repair in Las Vegas. For automated gate system troubleshooting, see our guide on an electric gate that won’t open, and for new operator installation, our gate installation page. We also publish a gate maintenance guide and cover gate welding and repair for structural issues.
Written by the team at Ironworks Gate Co. Summerlin, serving Summerlin.