Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Parts & Welding Across Sunrise Manor
If your driveway gate drags, your RV gate won’t latch, or a hinge post has started to lean, we can help. Ironworks Gate Co. handles gate parts and welding throughout Sunrise Manor, including the neighborhoods off East Charleston Boulevard and the streets that run toward the desert edge in 89110. We know how these gates were built here, and we know why they fail. Most of the gates we see in Sunrise Manor were hung by the homeowner or a previous owner, not by an HOA, and they’re older than the trucks in the driveway. Call (866) 623-9848 and a live person will answer, day or night.
Why Ironworks Gate Co. Summerlin Is Sunrise Manor’s Preferred Gate Parts & Welding Company
Sunrise Manor is its own kind of place. It’s an unincorporated pocket of the valley, older and working-class, and most of the gates here sit on privately owned lots with block-wall perimeters rather than the uniform tract gates you see across the line in North Las Vegas or Henderson. That difference matters when something breaks. There’s no builder standard to fall back on, no warranty desk to call. You need someone who can look at a one-off gate and figure out how it was put together, then fix the actual problem.
We’ve built a reputation in Sunrise Manor by doing exactly that: repairs that hold, welds that don’t crack six months later, and hardware that keeps working through another summer. We don’t carry parts on a truck, so when a job needs a specific hinge, roller, or control board, we order it and come back with the right piece instead of forcing a fit. Our technicians have up to 13 years of experience with gate hardware and welding, and every completed job is covered by our written 90-Day Done Right Promise – the Keystone Standard. If it isn’t right, we come back and make it right, no paperwork and no arguing.
We answer the phone around the clock, which matters when a gate won’t close at ten at night and your driveway is standing open. Calls from Sunrise Manor get the same straight answer whether it’s Tuesday morning or Sunday evening: we’ll tell you what’s wrong, what it will cost, and what we can do about it.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Gate Parts & Welding Services in Sunrise Manor
The work we do in Sunrise Manor tends to fall into a few familiar categories. Older gates, worn metal, and hardware that’s been baking in the sun for years. Here’s what we handle most often.
Hinge Replacement in Sunrise Manor
Worn hinges are the most common reason a swing gate sags and drags. On Sunrise Manor’s older wrought-iron and chain-link driveway gates, the hinges are often original and have lost their pin clearance, so the gate drops and scrapes the ground. We cut out the old hinges and weld in new ones sized to the gate’s weight, then re-hang the leaf so it swings true again.

Post Replacement in Sunrise Manor
When a hinge post has pulled loose from its footing or rusted through at the base, no amount of adjusting will fix the sag. This is common on the block-wall perimeters around 89110, where the gate post has taken decades of sun and shifting soil. We assess whether the post can be re-set or needs full replacement, then set the new post plumb and weld the gate hardware back into place.

Rail Repair in Sunrise Manor
Rails take a beating from windblown sand and from gates being pushed open past their stops. A bent or cracked rail throws the whole leaf out of square, and the gate never latches cleanly again. We straighten what can be straightened, cut out and weld in new rail sections where the metal is too far gone, and check the gate’s alignment before we leave.

Custom Welding in Sunrise Manor
Many Sunrise Manor properties have gates that were built on site to fit a particular opening, and there’s no catalog part that fits them. That’s where custom welding comes in. We fabricate hinge brackets, latch plates, and repair sections to match what’s already there, whether it’s wrought iron, steel tube, or a chain-link frame. If you want an RV gate that matches the look of your block-wall perimeter, we can build one that fits the opening and the style.
Trusted Brands We Service in Sunrise Manor
Gate operators in this part of the valley come in a handful of familiar makes. We’re trained and equipped to service LiftMaster, FAAC, DoorKing, and Mighty Mule systems, among others, so when your operator needs a control board, a limit switch, or a new set of safety edges, we know the platform. We don’t stock parts, but we source the correct replacement for your model and return to install it. For older systems where the factory part is gone, we’ll tell you plainly whether a retrofit kit will work or whether a new operator is the smarter spend. A square deal, quoted before we turn a bolt.
See the difference
Before
After
Before
After
Before
AfterCommon Gate Parts & Welding Problems We See in Sunrise Manor Homes
- Obsolete control boards on legacy operators. Plenty of Sunrise Manor driveways still run an older LiftMaster or FAAC unit whose control board is no longer made. We’ll check whether a retrofit board or kit is available before recommending a full operator replacement.
- Worn hinge posts and footings on manual swing gates. Years of sun-baked metal and desert grit wear the hinge pin and the footing at the same time, so the gate sags and binds. Sand caught in the rollers and tracks speeds this up.
- Gates hung before modern safety requirements. Older gates in Sunrise Manor often have no safety photocells or edge sensors at all. Where an operator is present, retrofitting UL 325 entrapment protection is the right call.
- Rack-and-pinion and roller wear on sliding gates. Windblown sand and grit grind away at the rack and the track rollers, so the gate hesitates or jams partway. Cleaning and re-aligning helps; replacing worn rollers and rack sections fixes it.
There’s a pattern to all of this, and it’s specific to where Sunrise Manor sits. On the east side near the desert edge, windblown sand and tumbleweed pile up against driveway and RV gates, and the swing from 100°F-plus afternoons to cold winter nights works gate hardware loose faster than in the sheltered parts of the valley. Metal expands and contracts every day, and over enough seasons that movement loosens bolts, opens weld seams, and wears hinge pins. If your gate needs attention every spring, that’s usually why – it’s the conditions, not bad luck.
A typical gate parts and welding call in Sunrise Manor involves an older swing gate or slide gate on a block-wall perimeter, where years of sun-baked metal and dust have worn the hinge post or the rack and pinion to the point of binding. The usual cause is a failed hinge post footing or a corroded operator control board. A qualified local pro will assess whether the post can be re-set or must be replaced, then correct the sag, weld new hinges, and retrofit safety photocells if an operator is present.
Pricing for Gate Parts & Welding in Sunrise Manor, NV
Here’s what the work generally runs in this part of the valley. A typical hinge replacement in Sunrise Manor runs $150 to $350 per gate, depending on how much old hardware has to be cut out. Replacing a hinge post runs $250 to $600, since setting a post plumb in a block-wall perimeter takes more time than a simple weld. Rail repair runs $120 to $400. Custom welding is quoted per job, usually $75 to $150 an hour plus material, and a full custom RV gate typically falls between $800 and $2,200. When an obsolete control board has to be replaced with a retrofit or a new operator, budget $350 to $900 depending on the platform.
Where your job lands in those ranges depends on the gate, the material, and how much corrosion we find once we open it up. We quote and agree on the price before any work starts, so the bill matches the quote. Estimates are free, and we’ll give you a second opinion on any written estimate you already have. There’s $50 off any repair over $250, and a standing 5% discount for seniors and veterans.
We Also Serve Cities Near Sunrise Manor
Sunrise Manor sits right next to several other communities we cover. We take gate parts and welding calls in Whitney, Winchester, Las Vegas, and North Las Vegas, and the work is much the same – older gates, worn hardware, and the honest question of repair versus replacement. If you’re on the Sunrise Manor side of the line and want to know whether your gate can be saved, our Gate Parts & Welding in Sunrise Manor team will give you a straight answer.
Serving Sunrise Manor, NV – Our Local Coverage Area
We serve Sunrise Manor and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs – Gate Parts & Welding in Sunrise Manor
It depends on the footing. In many cases the hinge post can be re-set and the gate re-hung, which is the cheaper fix. If the post has rusted through at the base or the footing is badly compromised, full replacement is the honest answer. We assess it on site and tell you which one you’re looking at before any work starts. Call (866) 623-9848 for a free estimate.
You have two real options: a retrofit control kit that adapts your existing operator, or a full operator replacement. Retrofit kits exist for some older LiftMaster units but not all, and availability changes by model. We check what’s still made for your system, quote both paths, and let you decide. Call (866) 623-9848 and we’ll look it up with you.
Yes, if your gate has an operator. Gates installed before modern entrapment protection standards were in place generally lack the photocells or edge sensors required under UL 325 today. Retrofitting them is a straightforward job and worth doing. Call (866) 623-9848 for a quote on the retrofit.
It wears them out faster than in sheltered parts of the valley. Windblown sand and grit work into the rollers and the rack, and the daily swing from 100°F-plus afternoons to cold nights loosens the hardware over time. Cleaning, re-lubricating, and replacing worn rollers keeps a gate running far longer. Call (866) 623-9848 to schedule a check.
Yes. We fabricate custom RV and driveway gates to fit your opening and match the style of your existing block wall, whether that’s wrought iron, steel tube, or chain-link frame. It’s a measured job, so we come out, take the measurements, and give you a written price before anything is ordered. Call (866) 623-9848 for a free measure and estimate.
Whether your gate needs a new hinge, a re-set post, or a weld that holds, we’d like to take a look. Ironworks Gate Co. serves Sunrise Manor and the surrounding valley with upfront pricing settled before the first bolt is turned, background-checked technicians, and a written 90-Day Done Right Promise behind every job. Call (866) 623-9848 for a free estimate. A live person answers, day or night.
Written by the team at Ironworks Gate Co.